Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Swift STP512B
Summary of Contents for Swift STP512B
- Page 1 SWIFT® STP512B Portable Thermal Printer User’s Manual (Ver 1.0)
-
Page 2: Table Of Contents
Content NOTICE .............................. 3 Notice of Safety ..........................3 Notice of Using..........................3 Notice of Storing ..........................4 Declaration ............................4 Chapter 1 Outer Appearance and Model No................5 1.1 Outer Appearance ......................5 1.2 Model No..........................5 Chapter 2 Characteristic Specification .................. -
Page 3: Notice
NOTICE Please read this manual carefully before using the printer! Notice of Safety Be sure to use the specified battery and power supply provided by our company. Otherwise it may cause fire, explosion or damage printer, meanwhile, the battery also may be damaged. If the printer would not be used for a long time, be sure to take off the battery, otherwise the battery may leak liquid which is corrosive liquid, if improper operation causes battery leak liquid, and it paste in the skin or clothes, please... -
Page 4: Notice Of Storing
Notice of Storing The printer should be placed in such an environment that the temperature is between-20℃ and 60℃, and the relative humidity is between 5% and 95%. If the printer will be stored for a long time, please be sure to take out the battery, otherwise may damage the battery and printer. -
Page 5: Chapter 1 Outer Appearance And Model No
Chapter 1 Outer Appearance and Model No. 1.1 Outer Appearance 1.2 Model No. STP512B Bluetooth modes, USB supported... -
Page 6: Chapter 2 Characteristic Specification
Chapter 2 Characteristic Specification 2.1 Printing Specification Printing Method: Thermal line Paper Width: 57.5mm±0.5mm； Effective Printing Width: 48mm Resolution: 8dots/mm (203dpi) Dots per line: 384dots Printing Speed: 62mm/s (Max) Paper Thickness: 0.06-0.08mm Printable Content: GB18030 Chinese characters, ASCII,self-defined character set, barcode EAN13, EAN8, images. 2.2 Physical Parameters Dimension (W×L×H): 106.5(L) X79.5(W) X47(H) mm Physical Weight:190g (excluding roll paper) -
Page 7: Chapter 3 Operation Method
low’ prompt tone if in the sleeping mode. ● Auto-sleeping: the printer will fall into sleep after in 2 seconds without button operation or receiving data , and can be awaken by pressing 【FEED】button or sending data to it. ● Battery Charging: quick charging, it will be fully charged ab hours; ●... -
Page 8: Paper Roll Installation
3.1.2 Paper Roll Installation 3.1.3 Others Opening and closing instructions: closing two side slowly by two hands at the same time Abnormal operation instructions: No blocking paper on the paper outlet Paper direction: Holding the printer in a flat-wise orientation during printing. Keep steady when running paper. -
Page 9: Paper Feeding (Manual Feeding)
time. Then loosen the【FEED】button and the current setting and status will be printed out. 3.2.4 Paper Feeding (Manual Feeding) When the printer works normally, hold down 【FEED】 button, the paper feeding begins, and stops when stopped holding the 【FEED】 button. When the printer works in black mark mode, hold down 【FEED】button, the printer begins to feed paper and stops at the position of black mark. -
Page 10: Printer Interface Connection And Printing
3.4 Printer Interface Connection and Printing 3.4.1 USB Connection The standard configuration of the STP512B printer is equipped with a standard USB TO Type-C cable for connecting the printer and the host device. The USB of the printer belongs to the type of slave device (DEVICE); the shape and pin... -
Page 11: Indicator And Buzzer
successfully. 3.5 Indicator and Buzzer There are three indicators - 【POWER】, 【BULETOOTH】and 【ERROR】. 【POWER】 indicator is red or green,【BLUETOOTH】indicator is blue and 【ERROR】 indicators is red. The below are the meanings of indicators: 【ERROR】indicator Constant on red lighting: printer out of paper Red light flashing (twice): it constants on lighting for 5s after flashing twice, this means over-voltage. -
Page 12: Description Of Pre-Printed Black Mark
4.2 Description of Pre-printed Black Mark If users use pre-printed black mark to locate the receipt, please be sure to abide by the following black mark pre-print regulation when print the black mark paper, otherwise, it will cause that the printer cannot identify the black mark. - Page 13 Baud rate: for Serial Interface only FEED FEED FEED 9600 19200 38400 57600 FEED FEED FEED FEED FEED 4800 2400 1200 115200 Language: Traditional FEED Simplified FEED Chinese Chinese FEED Font: FEED 12×24 9×17 FEED Density: FEED FEED High Medium FEED Sensor sensibility: FEED...