Advertisement
Quick Links
3425GW/3495GW
3425BGW/3495BGW
VERTICAL GAS
SMOKER
ASSEMBLER / INSTALLER:
Leave these instructions with the consumer.
CONSUMER / USER:
This instruction manual contains important information necessary for the proper assembly
and safe use of this appliance. Read and follow all warnings and instructions before
assembling and using this appliance. Follow all warnings and instructions when using this
appliance. Keep this manual for future reference.
DANGER:
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open door.
4. If odor continues, keep away from the
appliance and immediately call your fire
department. If a fire should occur, keep
away from the appliance and call your fire
department. Do not attempt to extinguish
an oil or grease fire with water.
Failure to follow these instruction could result in fire, explosion or burn hazard,
which could cause property damage, personal injury or death.
DANGER:
1. Never operate this appliance unattended.
2. Never operate this appliance within 10
feet (3.05M) of any other gas cylinder.
3. Never operate this appliance within 25
feet (7.5m) of any flammable liquid.
IM3425
Advertisement
Related Manuals for Landmann Great Outdoors Smoky Mountain 3425GW
Summary of Contents for Landmann Great Outdoors Smoky Mountain 3425GW
- Page 1 IM3425 3425GW/3495GW 3425BGW/3495BGW VERTICAL GAS SMOKER ASSEMBLER / INSTALLER: Leave these instructions with the consumer. CONSUMER / USER: This instruction manual contains important information necessary for the proper assembly and safe use of this appliance. Read and follow all warnings and instructions before assembling and using this appliance.
- Page 2 Cartersville, Georgia 30120 Service Note: If you are experiencing difficulties are are dissatisfied with your purchase, please contact Landmann at the telephone number listed above prior to returning your product to the store. For more information about growing family of Smokers,...
- Page 3 DO NOT use this smoker in a manner other than its intended purpose. It is not intended for commercial use. It is NOT intended to be installed or used in or on a recreational vehicle and/or boats. The smoker is not be used as a heater.
- Page 4 WARNING Use caution when operating the door while in operation. Keep hands, face and body safe from hot steam or flare ups. DO NOT wear loose clothing while operating the smoker. Tie back long hair while operating the smoker. ALWAYS wear fully-covering shoes while operating the smoker. Allow the smoker and its components to cool completely before conducting any routine cleaning or maintenance.
- Page 5 Assembly Step 1 - Identifying the parts Check your contents for these parts. If you are missing any parts or if any parts are damaged, please call our toll-free customer service line to order parts: 1-800-321-3473 DO NOT RETURN YOUR SMOKER TO THE RETAILER. PLEASE CALL US FIRST. 3425GW/3495GW Vertical Gas Smoker AZ002075 AZ002130...
- Page 6 Assembly Step 1 - Continued Check your contents for these parts. If you are missing any parts or if any parts are damaged, please call our toll-free customer service line to order parts: 1-800-321-3473 DO NOT RETURN YOUR SMOKER TO THE RETAILER. PLEASE CALL US FIRST.
- Page 7 Assembly Step 1 - Identifying the parts Check your contents for these parts. If you are missing any parts or if any parts are damaged, please call our toll-free customer service line to order parts: 1-800-321-3473 DO NOT RETURN YOUR SMOKER TO THE RETAILER. PLEASE CALL US FIRST. 3425BGW/3495BGW Vertical Gas Smoker AZ002075 AZ002130...
- Page 8 Assembly Step 1 - Continued Check your contents for these parts. If you are missing any parts or if any parts are damaged, please call our toll-free customer service line to order parts: 1-800-321-3473 DO NOT RETURN YOUR SMOKER TO THE RETAILER. PLEASE CALL US FIRST.
- Page 9 Assembly Step 2 Vent Damper Plate with plastic tab guard Phillips Head Screwdriver Hardware Bag 1/2” Wrench #10-24 nut #10-24 lock washer #10-24 x 5/8” bolt 2 required 2 required 2 required 1. Remove all loose inner packages from inside cabinet. Set the cabinet assembly top side down. To prevent scratching or damage to your smoker, set the cabinet on a padded surface like cardboard or carpet.
- Page 10 Assembly Step 3 Cabinet Assembly 4 Legs Phillips Head Screwdriver Hardware Bag 1/4-20 x 5/8” bolts 8 required 1. For each leg, line up the holes and insert the bolts. Nuts are pre-welded to the cabinet. The back legs bolts should be inserted and securely tightened.
- Page 11 Assembly Step 4 Phillips Head Control Panel Assembly Screwdriver Hardware Bag 1/4-20 x 5/8” bolts 10#-24 x 1/2” bolts 2 remaining bolts from Step 2 2 required 1. Place the control panel assembly between the front legs as shown. Insert the two (2) remaining bolts 1/2 way. DO NOT tighten them until the next step has been finished.
- Page 12 Assembly Step 5 Phillips Head Screwdriver Hardware Bag 1/4-20 x 1/2” bolts 3 required 1. Set the burner assembly onto the cabinet as shown. IMPORTANT: The burner tube must slide properly onto the brass valve stem as shown below. An improper fit will result in poor gas flow and operation of the smoker.
- Page 13 Assembly Step 6 Adjustable Chimney Phillips Head Screwdriver Hardware Bag 1/4-20 x 5/8” bolts 3 required 1. Turn the smoker upright. Ideally, it needs 2 people to lift the smoker up. Carefully tilt the cabinet on the side legs, grasp the empty hole for the adjustable chimney and pull up gently until smoker is upright on all four legs.
- Page 14 Assembly Step 7 Phillips Head Screwdriver 2 Side Carry handles Hardware Bag 1/2” Wrench 1. Align the side carry handle with the corresponding holes on the side of the cabinet. Then handles must be positioned upright with the bolt holes on the bottom.
- Page 15 Assembly Step 8 Wood Chip Box Wood Chip Box Lid Wood Chip Box Stand...
- Page 16 Assembly Step 9 Cooking rack Water Pan No tools or hardware are required for this step. 1. Slide water pan into the rack directly above the wood chip box. 2. Insert the cooking racks into remaining positions and use as desired. For gest accesss, the cooking rack grid wires should run from front to back as shown.
- Page 17 Assembly Step 10 Hardware Bag Phillips Head Screwdriver 1. Slide the handle washer onto the end of the door handle, followed by the handle spring as shown. 2. Feed the door handle into the hole through the front of the door panel. 3.
- Page 18 Assembly Step 11 Hardware Box Name-plate Temperature Gauge 2 wingnuts 2 flat washers NOTE: No tools or hardware are required for this step. 1. Insert the Temperture Gauge mounting pins through the mounting holes in the front of the door panel. 2.
- Page 19 Assembly Step 12 Hardware Bag Insert the R-Hook into the pre-threaded mount on the front legs as shown. And firmly tighten it. Using the zip tie, secure the hose to the front leg as shown. Do not pull the zip tie tight - leave it just lose enought so the hose can be adjusted if needed.
-
Page 20: Connecting The Lp Cylinder
CONNECTING THE LP CYLINDER WARNING ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED TO PREVENT FIRE, DAMAGE AND/OR INJURY. IMPORTANT: Any fuel supply cylinder used must be constructed and marked in accordance with specifications for propane cylinders of the U.S. Department of Transportation (DOT) CFR 49, or CAN/CSA B339. - Page 21 CONNECTING THE LP CYLINDER - Continued WARNING ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED TO PREVENT FIRE, DAMAGE AND/OR INJURY. Valve/pressure regulators are factory set to the correct operating pressures. NO attempts should be made to adjust these settings.
- Page 22 OPERATING INSTRUCTIONS PRE-USE PROCEDURES: Before you cook food in our smoker, it is important to “season” your smoker. Seasoning seals the paint and interior of your smoker to enhance flavoring, durability and overall peformance. This is also referred to as the “break-in”...
- Page 23 ADDING WOOD CHIPS To add wood chips before smoking, fill the wood chip box with your choice of flavoring hardwood chips. The amount and type of wood you use is entirely up to you. One full filling of the wood chip box is typically enough for several hours of smoking.
-
Page 24: Lighting Procedures
LIGHTING PROCEDURES: Igniter Lighting System: 1. Check all connections for leaks using the “soapy water” test as explained on page 21. 2. Open the smoker cabinet door. 3. Check for any blockage to the venturi tube or burner. Remove any foreign objects or matter. 4. -
Page 25: Cooking Instructions
COOKING INSTRUCTIONS: IMPORTANT: Before each use, clean and inspect the hose and the connection to the LP cylinder. If there is evidence fo abrasion, wear, cuts or leaks, the hose must be replaced before the smoker is used. Refer to the “Leak test instructions” in the LP Cylinder portion on this instruction manual. * Fill the wood chip box with flavoring wood chips and place the box with lid on, inside the smoker as instructed in the assembly section of this instruction manual. -
Page 26: Temperature Chart
TEMPERATURE CHART Here is a chart for measuring properly cooked meat temperature: (USDA Standard) CAUTON The below temperatures are measured with a meat probe thermometer. The heat indicator on the door of the smoker SHOULD NOT be used as an accurate meat temperature reading. -
Page 27: After Use Safety
AFTER USE SAFETY WARNING Use caution when lifting or moving the smoker to avoid strains or back injury. Two (2) people are recommended to lift or move the smoker. DO NOT place cover on smoker if the smoker is still hot. DO NOT store the smoker near gasoline or other combustible liquids or where combustible vapors may be present. - Page 28 AFTER USE CARE AND MAINTENANCE CAUTION: All care and maintenance procedures are to be performed only while the smoker is turned off and completely cooled. To clean, remove the water pan, wood chip box and cooking racks from the smoker. Clean with hot, soapy water and rinse and dry thoroughly.