Related Manuals for USX-MOUNT SMS012-L-01
Summary of Contents for USX-MOUNT SMS012-L-01
- Page 1 SMS012-L-01 INSTRUCTION MANUAL For 13-42" TV If you have any questions along the way, just give us a mail to customerservice@usxstar.com. We’re ready to help! USA-A0...
- Page 2 Before getting started, let’s check below lists to make sure it is just right for you! MAX:200mm/7.87" (MIN:75mm/2.95") Check your TV VESA is within No? This mount is NOT compatible. Min and Max size MAX:200mm/7.87" (MIN:75mm/2.95") Yes? Perfect ! CAUTION: DO NOT exceed the maximum weight Does your TV No? Perfect –...
- Page 3 TV INTERFACE 200mm [7.87in] 75mm 200mm [2.95in] [7.87in] 75mm [2.95in] WALL PLATE TOP VIEW - EXTENDED SIDE VIEW - EXTENDED Ø7mm +5° 92mm [Ø0.28in] [3.62in] 213mm 360mm [8.39in] 189mm [14.17in] [7.44in] -15° 51mm [2.01in] FULLY ASSEMBLED MOUNT TOP VIEW - RETRACTED SIDE VIEW - EXTENDED 231mm [9.10in]...
- Page 4 WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service.
- Page 5 Parts and Hardware for STEP 2 Lag Bolt Wall Plate Unit Contact us and mail to customerservice@usxstar.com. to have these additional pieces shipped directly to you. Concrete Wall Anchor 3pcs M6x8mm Bolt Allen Key Velcro x3 1-1 Disassemble Wall Plate Unit into Two Pieces Wall plate TV plate ①...
- Page 6 1-2 Choose Configuration If your TV VESA size is above 100*100mm, you need to assemble extended arms onto TV plate using bolts and Alley key per below option 3 - option 5 shown. Option 3 ⑤ ⑤ Option 1 Option 2 ④...
- Page 7 1-3 Select TV Screws...
- Page 8 1-5 Attach the TV Plate 1-4 Need Spacer? No, choose suitable screws and washers. VESA≤100X100mm Yes, choose suitable screws, washers and spacers. Tips: If you need to combine M6/M8(c/e/f) screws with 100X100mm<VESA≤200X200mm 2.5mm spacers( i ), you have to remove the inner circle.
- Page 9 CAUTION: Avoid potential personal injury or property damage! ● Drywall covering the wall, must not exceed 5/8 in. (16 mm) ● Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm) ●...
- Page 10 3. Drill pilot holes using a 1/8 in. (3mm) diameter drill bit. IMPORTANT: Pilot holes must be drilled to a depth of 2.16 in. (55 mm). Be sure to drill into the center of the studs. 4. Install wall plate using three lag bolts .
- Page 11 CAUTION: Avoid potential personal injury or property damage! ● Mount the wall plate assembly directly onto the concrete surface ● Minimum solid concrete thickness: 8 in. (203 mm) 1. Position the wall plate on the wall at your desired height. Level the wall plate and mark the hole locations.
- Page 12 3. Insert four anchors. CAUTION: Be sure the anchors are seated flush with the concrete surface. 4. Insert wall plate using three lag bolts .Tighten the lag bolts only until they are pulled firmly against the wall plate. CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
- Page 13 Before hanging TV, please try to pull the mount to make sure that it has been assembled on the wall tightly. Wall plate...
- Page 14 ① ①...
- Page 15 5-1 Tilting angle adjustment (+5°/-15°) ： Pull TV to your desired angle then fasten 2 tilting bolts with allen key +5° Tighten Tilting bolts Loosen -15° -15° +5° Tighten Tilting bolts Loosen...
- Page 16 5-2 Cables manage: Manage TV cables orderly and guide them through the velcros. Velcro...
Need help?
Do you have a question about the SMS012-L-01 and is the answer not in the manual?
Questions and answers