Subscribe to Our Youtube Channel
Related Manuals for USX-MOUNT SMS007-1
Summary of Contents for USX-MOUNT SMS007-1
- Page 1 SMS007-1 INSTRUCTION MANUAL For 26-42" TV If you have any questions along the way, just give us mail to customerservice@usxstar.com. We’re ready to help!
- Page 2 Before getting started, let’s check below lists to make sure it is just right for you! MAX:200mm/7.87" (MIN:100mm/3.94") Check your TV VESA is within No? This mount is NOT compatible. Min and Max size MAX:200mm/7.87" (MIN:100mm/3.94") Yes? Perfect ! CAUTION: DO NOT exceed the maximum weight Does your TV No? Perfect –...
- Page 3 TV INTERFACE MAX:200mm[7.87in] MIN:100mm[3.94in] MAX:200mm [7.87n] MIN: 100mm [3.94in] WALL PLATE SIDE VIEW - RETRACTED +5° Ø9mm [Ø0.35in] 145mm [5.71in] -15° FULLY ASSEMBLED MOUNT TOP VIEW - RETRACTED TOP VIEW - EXTENDED 80mm [3.15in] +15° -15° 200mm 226mm [7.87in] 78mm [8.90in] [3.07in] 226mm...
- Page 4 WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service.
- Page 5 Parts and Hardware for STEP 2 Allen Key Lag Bolt Contact us and mail to customerservice@usxstar.com. to have these additional pieces shipped directly to you. Concrete Wall Anchor 2pcs...
- Page 6 1-1 Disassemble Wall Plate Unit into Two Pieces TV plate ① Wall plate 1-2 Choose Correct Configuration Per VESA Size on the Back of Your TV. ③ ③ ① ① ② ② ① 100X100 ② 200X100 ③ 200X200 ② ① ①...
- Page 7 1-3 Select TV Screws...
- Page 8 1-5 Attach the TV Plate 1-4 Need Spacer? No, choose suitable screws and washers. Yes, choose suitable screws, washers and spacers. Tips: If you need to combine M6/M8(c/e/f) screws with 2.5mm spacers( i ), you have to remove the inner circle.
- Page 9 CAUTION: Avoid potential personal injury or property damage! ● Drywall covering the wall, must not exceed 5/8 in. (16 mm) ● Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm) ●...
- Page 10 3. Drill pilot holes using a 1/8 in. (3.18 mm) diameter drill bit. IMPORTANT: Pilot holes must be drilled to a depth of 2.16 in. (55 mm). Be sure to drill into the center of the studs. 4. Install wall plate using lag bolts .
- Page 11 CAUTION: Avoid potential personal injury or property damage! ● Mount the wall plate assembly directly onto the concrete surface ● Minimum solid concrete thickness: 8 in. (203 mm) 1. Position the wall plate on the wall at your desired height. Level the wall plate and mark the hole locations.
- Page 12 3. Insert anchors. CAUTION: Be sure the anchors are seated flush with the concrete surface. 4. Insert wall plate using lag bolts .Tighten the lag bolts only until they are pulled firmly against the wall plate. CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
- Page 13 Before hanging TV, please try to pull the mount to make sure that it has been assembled on the wall tightly. 66 LBS (30 kg)
- Page 14 Hang pre-assembled TV unit on the wall plate and fix them using screws ①. ①...
- Page 15 5-1 TV leveling adjustment (±4°): Loosen 2 leveling bolts on the rear of TV plate by maximum 2 turns, adjust to level and retighten to secure. ±4° Loosen Tighten...
- Page 16 5-2 Tilting angle adjustment (+5°/-15°) ： Loosen handle and tilting bolt, adjust TV to your desired position, then tighten handle and tilting bolt. +5° Tilting bolts +5° -15° Tilting bolts -15°...
Need help?
Do you have a question about the SMS007-1 and is the answer not in the manual?
Questions and answers