Advertisement
BRIEF OF PRODUCT
* Sensor (CCD)
Adopt SONY 1/3" CCD Sensor.
* Auto Gain Control (AGC)
Built-in auto gain control (AGC) circuit. The color camera
can get high definition picture in low Lux condition.
* Scanning Mode
NTSC or PAL mode.
* OSD SETTING
MANUAL
LENS
TYPE:DC/VIDEO
AUTO
MODE:CLOSE/AUTO/OPEN SPEED:0-255
HIGH LUMINANCE MODE:SHUT+AUTO IRIS/AUTO
BRIGHTNESS:0-255
AUTO
LOW LUMINANCE MODE:OFF/AGC
SHUTTER/
BRIGHTNESS: ×0.25, ×0.5, ×0.75, ×1
AGC
MODE:SHUT+AGC
SHUTTER:1/50,1/120,1/250,1/500,1/1000,1/2000,
MANUAL
1/4000,1/10000
AGC:6,12,18,24,30,36,42,44.8
ATW
SPEED/DELAY CNT/ATW FRAME/ENVIRONMENT
WHITE BAL
PUSH/ANTI CR/PUSH LOCK/USER1/USER2/MANUL
BACK LIGHT
OFF/BLC/HLC
PICT
MORROR/BRIGHTNESS/CONTRAST/SHARPNESS/HUE/GAIN
ADJUST
OFF
OSD SET
ATR
ON
LUMINANCE/CONTRAST
OFF
MOTION
DET
DETECT SENCE/BLOCK DISP/MONITOR AREA/
ON
AREA SEL/TOP/BOTTOM/LEFT/RIGHT
OFF
PRIVACY
AREA SEL/TOP/BOTTOM/ LEFT/RIGHT/
ON
COLOR/TRANSP/MOSAIC
COLOR
B/W
BURST:OFF/ON
DAY/NIGHT
BURST:OFF/ON
AUTO
DELAY CNT/DAY-NIGHT/NIGHT-DAY
NR
NR
MODE:Y/C,OFF,Y,C
CAMERA ID OFF/ON
SYNC
INT
ENGLISH/CHINESS/JAPANESS/ESPANOL/PORTUGUES/
LANGUAGE
PYCCKNN/FRANCAIS/DEUISCH
CAMERA RESET/BACK/EXIT/SAVE ALL
CONNECTING
KEY BOARD
UP
LEFT
DOWN
IRIS
TROUBLE AND SOLUTION
1. No Picture after providing power
. May be the power supply voltage abnormity, please check the power
supply voltage and pole whether exactitude.
. Please check all the connecting cable and monitors whether be connected
correctly or not.
2. The picture level direction have flowing interference ripples
. May be caused by the power supply AC ripples, it need filter the wave of the
power supply.
. Check the monitor and peripheral equipments used.
3. The picture background color changes continuously
. The fluorescent lamp's electromagnetic field cause color roll. This is proper
phenomenon of the cameras.
. Reduce the fluorescent lamp numbers or increase the distance between the
camera and the fluorescent lamps can improve it.
. Use power supply external sync. camera can solve it.
4. The picture smear too mass
. The power supply's voltage unstable.
. Connecting cables not connect correctly or have high impedance.
Notes：
●The power supply must through safe attestation. Its output voltage,
current, voltage polarity and operating temperature must match the
camera's requirement.
●When using the camera in the thunderbolt condition,please note to
mount Anti-thunder device or put off the power supply plug and cable.
●In order to capture high quality pictures, the power supply's cable and
video output cable should not be too long.
Monitor
KDP-673SH20
MENU
Link wire rule：
RIGHT
Video
Power
PRESS
DC12V Power Supply
INTRODUCTION
Congratulations on your purchase of this product.
This User Guide suits
KDP-673SH20
adopt the latest SONY technical of sensor and driver. The
Video
most attractive characteristics are small and easy hidden,
suits the elevator and corridor. In addition, it owns the
characters of high definition and stability, strong anti-
jamming, rich and real color. Fixing and using this model
are convenient too. It is very good for you to apply to your
DC12V
CCTV system.
Please read this instruction manual carefully to
ensure proper use of the product.
To prevent fire or shock hazarded. Do not expose the unit
to rain or moisture.
The symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
Instructions in the literature accompanying the appliance.
The symbol is intended to alert the user to the presence of
uninsulated 'dangerous voltage' within the product's
enclosure that may be of sufficient Magnitude to constitute
a risk of electric shock to persons.
RISK OF ELECTRIC. DO NOT OPEN
CAUTION:
SHOCK
DO NOT REMOVE COVER OR BACK NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
CAUTION:
TO PREVENT ELECTRIC SHOCKS AND RISK OF
FIRE HAZARDS, DO NOT USE OTHER THAN
SPECIFIED POWER SOURCE.
Note:
● Please note the camera's operating temperature and its using
environment requirement. Avoid using the camera at too high or
too low temperatures. The operating temperature is -30~+60℃.
(Recommendatory operating temperature is -10~+45℃.)
● Never make the camera face the sun or bright object.
Otherwise, it will damage the CCD.
● Do not mount the camera near by the radiator or heater.
series product. We
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
Advertisement
