Table of Contents
Advertisement
Quick Links
radio bus
Radio wall transmitter flat - 1gang, 2gang, 4gang
Radio wall transmitter 1gang flat
Order-No. : 2721 xx
Radio wall transmitter 2gang flat
Order-No. : 2722 xx
Radio wall transmitter 4gang flat
Order-No. : 2724 xx
Operation- and
Assembly Instructions
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Failure to observe the instructions may cause damage to the device and result in fire and
other hazards.
Keep button cells out of reach of children! If button cells are swallowed, get medical help
immediately.
Risk of explosion! Do not throw batteries into fire.
Risk of explosion! Do not recharge batteries.
The radio communication takes place via a non-exclusively available transmission path,
and is therefore not suitable for safety-related applications, such as emergency stop and
emergency call.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
(1) Base plate
(2) Frame
(3) Radio wall transmitter
(4) Fastening screw
(5) Labelling field
(6) Cover
82532711
97-09322-000
picture 1
Seite 1/7
13.08.2010
Advertisement
Table of Contents
Related Manuals for Berker 2721 Series
Summary of Contents for Berker 2721 Series
- Page 1 radio bus Radio wall transmitter flat - 1gang, 2gang, 4gang Radio wall transmitter 1gang flat Order-No. : 2721 xx Radio wall transmitter 2gang flat Order-No. : 2722 xx Radio wall transmitter 4gang flat Order-No. : 2724 xx Operation- and Assembly Instructions 1 Safety instructions Electrical equipment may only be installed and fitted by electrically skilled persons.
- Page 2 radio bus Radio wall transmitter flat - 1gang, 2gang, 4gang 3 Function System information By statute, the reception characteristics and the antenna cannot be changed. The device may be operated in all EU and EFTA countries. The declaration of conformity can be viewed on our website. The range of a radio system from the transmitter to the receiver depends on various circumstances.
- Page 3 radio bus Radio wall transmitter flat - 1gang, 2gang, 4gang 4 Operation Channel assignment of the wall transmitter picture 3: Channel assignment 1-gang, 2-gang, 4-gang Sending radio telegrams Press channel button, e.g. 1+, to transmit a radio telegram. The corresponding LED lights up as an acknowledgement. As long as no light scene functions were selected, the following responses occur, depending on the type of receiver: Button...
- Page 4 radio bus Radio wall transmitter flat - 1gang, 2gang, 4gang First the old light scene is called up; do not release the button during this. After about 3 seconds the new light scene is saved and activated. i If during saving of a light scene the blind is not in an end position, or is on the way there, then that blind is not integrated into the light scene.
- Page 5 radio bus Radio wall transmitter flat - 1gang, 2gang, 4gang picture 4: Remove battery Remove empty battery carefully using a screwdriver. picture 5: Insert battery i Keep contacts of batteries and device free of grease. Apply new battery to the positive contact of the battery holder. Observe polarity: the positive pole of the battery must be at the top.
- Page 6 radio bus Radio wall transmitter flat - 1gang, 2gang, 4gang picture 6: Function switch i In the state as delivered all function switches are set to the ON position. Select functions of the buttons with the function switches according to the following table . Function switch Button bottom...
- Page 7 Our products are under guarantee within the scope of the statutory provisions. If you have a warranty claim, please contact the point of sale or ship the device postage free with a description of the fault to the appropriate regional representative. Berker GmbH & Co. KG Klagebach 38 58579 Schalksmühle/Germany...
Need help?
Do you have a question about the 2721 Series and is the answer not in the manual?
Questions and answers