Advertisement

Quick Links

MaxiCut 5-60
UseR MAnUAL edition 2-05
2012-10-23
serial number:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MaxiCut 5-60 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for HYDROSCAND MaxiCut 5-60

  • Page 1 MaxiCut 5-60 UseR MAnUAL edition 2-05 2012-10-23 serial number:...
  • Page 2 High quality and reliable performance in a demanding environment was the primary focus. Downtime and unnecessary service is always more expensive than the small extra cost of a quality product. That was the philosophy and still is for what became Hydroscand Machine AB in Säter, 20 years ago.
  • Page 3: Table Of Contents

    Contents 1. INTRODUCTION ........4 2. GENERAL pRECAUTIONS ......5 3. EqUIpMENT ..........6 3.1 WARRANTY ........6 3.2 IMpORTANT ........6 4. MACHINE ..........7 4.1 IDENTIfICATION ......... 4.2 DESCRIpTION ........7 5. CONTROL pANEL ........8 6. STARTING Up .......... 9 6.1 pRELIMINARY STEpS ......
  • Page 4: Introduction

    MUst read the following instructions be- fore operating. Hydroscand Machine AB declines any responsability for damage to persons, things or to the machine itself, arising fromits incorrect use, neglience and superficial interpretations of safety concepts in this manual.
  • Page 5: General Precautions

    Technical Service. The use of spares that do not respond to the specifications listed below, changes or manipulations - however slight- shall exempt Hydroscand Machine AB from any responsability regarding the proper use and functioning of the cutting machine and safety of peole and/or property.
  • Page 6: Equipment

    It’s the customers responsibility to install the power supply according to present national regulations. The manufacturer recommends a lockable main switch bet- ween the machine and the mains. MaxiCut 5-60 OT is prepared with a smoke eva- cuation connection and if a smoke evacuation is connected the manufacturer re- commends to install a spark filter to prevent hazards.
  • Page 7: Machine

    5 bar. The hose cutting machine must only be used for hydraulic hoses compatible with the specifications below. Follow the environmental conditions and limitations recommended by Hydroscand Machine AB and current health and safety regula- tions. note ! the descriptions includes the use for which the machine has been designed, built and protected.
  • Page 8: Control Panel

    MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23 5. Control panels 1. emergency stop button 2. start and stop 3. Hold for counter Keep the button pressed down as long as you do not wish to count the cuttings. E.g when clean cutting, press the button and keep it pressed down during the whole cutting process.
  • Page 9: Starting Up

    MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23 6. starting - up 6.1 Preliminary steps Important! It is essential to determine size measurements and placement in advance in order to ensure safe placement, running and emergency actions within the surrounding environment. these conditions should be respected beginning with the preliminary stages, before cutting begins.
  • Page 10: Hose Cutting

    If excessive smoke or heat is generated or if the motor stalls when cutting the hose adjust the speed to optimize the cut. Contact Hydroscand Machine AB for further information about adjusting the speed.
  • Page 11: Maintenance

    MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23 8. Maintenance 8.1 Replacing the cutting blade Warning ! Always use protective gloves when changing the cutting blade. • Turn off and disconnect the power supply to the machine. Lock switches if pos- sible.
  • Page 12: Reset The Motor Protection

    MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23 8.4 Reset the motor protection switch . Warning! Electrical power, do not touch • Open the electric box hatch wire/terminals. • Push the blue reset button on the switch. • Close the hatch and restart the machine.
  • Page 13: Technical Data

    10 technical data 10.1 noise Level Test result of measuring noise level on MaxiCut 5-60 OT. This result is to be consi- dered as a guiding reference value and it is not performed under any ISO standard regulations or similar. The test is made at two different steps, fi rst at idle speed and second when cutting a ½”...
  • Page 14 MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23...
  • Page 15 MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23...
  • Page 16 MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23...
  • Page 17 MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23...
  • Page 18 MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23...
  • Page 19 MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23...
  • Page 20 MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23...
  • Page 21 MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23...
  • Page 22 MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23...
  • Page 23 MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23...
  • Page 24 MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23...
  • Page 25 MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23...
  • Page 26 MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23...
  • Page 27 MaxiCut 5-60 USER MANUAL EDITION 2-05 2012-10-23...
  • Page 28 Pungmakarbovägen 1, SE-783 90 Säter, Sweden Phone: +46-(0)225-573 30 Fax: +46-(0)225-501 08 info@hydroscand-machine.se www.hydroscand-machine.se...

Table of Contents