Related Manuals for Turnstiles OTSG9000 Series
Summary of Contents for Turnstiles OTSG9000 Series
- Page 1 User Manual Speed gates OTSG9000 series Applicable Model(s): OTSG9000, OTSG9011, OTSG9022, OTSG9033, OTSG9200, OTSG9211, OTSG9222, OTSG9233 Version: 1.0 Date: June 2019...
-
Page 2: Table Of Contents
3. Menus ......................................9 3.1 Menu operations ................................9 3.2 Menus ...................................... 9 3.3 Functions introduction of wiring and terminal ..................12 4. Troubleshooting ..................................13 5. Product Maintenance ................................14 5.1 Chassis ....................................14 5.2 Movement ..................................14 5.3 Power .....................................14 www.TURNSTILES.us | patrick.mcallister@TURNSTILES.us | 303-670-1099... -
Page 3: Product Introduction
The SUS304 stainless steel body looks simple and clean and is anti-corrosion. The turnstile grants legal access to the authorized persons and restricts illegal access. In case of an emergency, the lock will release to allow fast evacuation and egress. Below is the design and dimensions of OTSG 9000: www.TURNSTILES.us | patrick.mcallister@TURNSTILES.us | 303-670-1099... -
Page 4: The Mechanical System Of The Speed Gates
Mode indicator: This indicator shows the current passing mode status of the channel and guides the passenger to pass the passage orderly and safely. Loudspeaker: The system will trigger the alarm if it detects any unauthorized entry to the lane. www.TURNSTILES.us | patrick.mcallister@TURNSTILES.us | 303-670-1099... -
Page 5: Operation Principle Of The Speed Gates
The alarm signal will not be cancelled until the passenger retreats from the passage. A pedestrian can pass through the lane only after successful verification with a valid card read by the card reader. www.TURNSTILES.us | patrick.mcallister@TURNSTILES.us | 303-670-1099... -
Page 6: System Composition Of The Product
AC110~240V, 50-60Hz Input control signal Switching signal Output voltage DC 24V Time of 20% - 95% 0.8 Sec (adjustable) Relative humidity opening/closing (Non-condensing) Temperature Passage rate Maximum 30/minute -28℃ to 60℃ Infrared sensor Working environment Indoor www.TURNSTILES.us | patrick.mcallister@TURNSTILES.us | 303-670-1099... -
Page 7: Installation Of The Product
A distance of 100mm between the speed gates turnstile and the wall needs to be reserved for ease of opening the top cover of the machine to perform maintenance and adjustment. The reference figure is shown below: www.TURNSTILES.us | patrick.mcallister@TURNSTILES.us | 303-670-1099... -
Page 8: Cables Installation And Fixing
100mm. In addition, the conduit outlet is bent to prevent the ingress of water into the conduit. Installation holes and cabling positions are as shown in Figure 2-3a: www.TURNSTILES.us | patrick.mcallister@TURNSTILES.us | 303-670-1099... - Page 9 Figure 2-3a. Use a hammer drill to drill M12 screw holes, then install the screws. Place the swing turnstile according to the size and respective installation position as shown in the figure before installation and fixing. Connect the turnstile to the power supply and www.TURNSTILES.us | patrick.mcallister@TURNSTILES.us | 303-670-1099...
- Page 10 If the test is passed, tighten the screws. It is recommended to mark a warning line on the ground, as shown in Figure 2-3b, after installing the device to remind the pedestrian to stand behind the line when swiping the card. Figure 2-3b www.TURNSTILES.us | patrick.mcallister@TURNSTILES.us | 303-670-1099...
-
Page 11: Menus
1. Position adjustment of the swing barrier Type: zero (default) Left limit Right limit 2. Passing mode Opening mode: Two-way swipe (default) Left free, Right swipe Left swipe, Right free Two-way free Left prohibit, Right swipe www.TURNSTILES.us | patrick.mcallister@TURNSTILES.us | 303-670-1099... - Page 12 Do not allow card swiping in the channel 9. Reset counter Reset: Out counter (default) Into the counter 10. Gate closing delay time Time: 0~10 (default 0) 11. Brake unlock mode Mode: Delay unlock (default) www.TURNSTILES.us | patrick.mcallister@TURNSTILES.us | 303-670-1099...
- Page 13 Area selection: Disable during In and out of infrared (default) All infrared zone anti-pinch 18. Memory opening Whether to open: No (default) 19. System working mode Mode: working mode (default) Test mode Restore to factory 20. Version number: Version: V9.0.0 www.TURNSTILES.us | patrick.mcallister@TURNSTILES.us | 303-670-1099...
-
Page 14: Functions Introduction Of Wiring And Terminal
3.3 Functions introduction of wiring and terminal Figure 3-2 www.TURNSTILES.us | patrick.mcallister@TURNSTILES.us | 303-670-1099... -
Page 15: Troubleshooting
When the gate is self-tested, the swing In the process of self-test, there are arm is not in the normal closing obstacles, please remove the obstacles, position! restart the self-test after power-on! www.TURNSTILES.us | patrick.mcallister@TURNSTILES.us | 303-670-1099... -
Page 16: Product Maintenance
Caution: The above-mentioned maintenance method of the speed gates, especially the movement and the electric control maintenance, must be carried out by professional personnel. Always remember to cut off the power supply before maintenance and repair. www.TURNSTILES.us | patrick.mcallister@TURNSTILES.us | 303-670-1099...
Need help?
Do you have a question about the OTSG9000 Series and is the answer not in the manual?
Questions and answers