Floor iQ VLFR-220R User Manual
  1. Manuals
  2. Brands
  3. Floor iQ Manuals
  4. Power Tool
  5. VLFR-220R
  6. User manual

Floor iQ VLFR-220R User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

1
 
 
F
Q
VLFR-­220R/VLFR-­380R  
LOOR  I
 
User Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VLFR-220R and is the answer not in the manual?

Questions and answers

Related Manuals for Floor iQ VLFR-220R

Summary of Contents for Floor iQ VLFR-220R

  • Page 1     VLFR-­220R/VLFR-­380R   LOOR  I   User Guide...

  • Page 2: Table Of Contents

      TABLE OF CONTENTS INTRODUCTION page 2 DEVICE DESCRIPTION page 2 Applications Accessories Safety device SAFETY INSTRUCTIONS page 3.4 Environmental requirements Protective equipment Electrical hazards Cutting blades Warning symbols COMPULSORY CHECKS BEFORE START-UP page 5 OPERATION page 6.7 Removing the cutting blade Fitting the cutting blade Setting the depth Enable/Disable...

  • Page 3: Introduction

    INTRODUCTION Thank you for choosing a Floor IQ floor milling machine. This user guide describes the VLFR semi-self-propelled floor milling machine. This user guide contains important information to ensure your machine is operated correctly and safely. Read this user guide carefully before using the semi-self-propelled floor milling machine.

  • Page 4: Safety Instructions Page

    SAFETY INSTRUCTIONS Read the following safety instructions carefully before using the floor milling machine. Follow these safety instructions during use. STORE THE SAFETY INSTRUCTIONS with the machine so they can be consulted whenever required. Environmental requirements •   NEVER use the floor milling machine in the vicinity of flammable liquids or gases.

  • Page 5: Electrical Hazards

    Electrical hazards •   Always connect your power cord to a fuse box with a circuit breaker. Use a fuse with a rating up to 16 A. •   NEVER use the milling machine in a wet or damp location. •...

  • Page 6: Compulsory Checks Before Start-Up

    COMPULSORY CHECKS BEFORE START-UP The following checks are required before starting up the floor milling machine. The milling machine must NEVER be used if one or more of the following checks show either the power supply or the machine is not working correctly.

  • Page 7: Operation

    OPERATION During the operation of the milling machine, the following additional safety instructions must be followed. Only work with an earthed power cable of the proper thickness (at least 2.5 Ensure the machine is NEVER placed under undue load while milling. NEVER stop the cutting blade movement by applying pressure to the sides.

  • Page 8: Maintenance

    Switching the machine on and off Switching on 1   Always turn on your vacuum cleaner before the milling machine. 2   Pull the red emergency stop button outwards. 3   Press the black button beside the emergency stop. 4   Allow the machine to reach the operating speed.

  • Page 9: Technical Data

    Technical data Number of cutting blades Max. blade width : 18 mm Max. cutting blade diameter : 120 mm Min. cutting depth : 1 mm Max. cutting depth : 24 mm Blade (shaft hole) : 22.2 mm Power supply : 230 V or 400 V Revolutions per minute : approximately 6,800 rpm Noise level...

  • Page 10: Parts List For Machine

    Parts list for machine number article number amount Description VLFR1 Plastic handles VLFR2 Thermal protection and emergency stop switch VLFR3 Nut for the articulation mechanism VLFR4 Articulation rod, two-piece VLFR5 Bottom plate for machine VLFR6 Bolt for rear wheels VLFR7 Ball bearing for rear wheels VLFR8 Rings for rear wheels...

This manual is also suitable for:

Vlfr-380r

Table of Contents