Advertisement
Quick Links
Installing Washify Controller Integration
Table of Contents.
1. Mounting the Enclosure
Step 1. Metal Fins
Step 2. Lag Fins to the Wall
Step 3. Verify Mounting
2. Providing Power and Network
Step 1. Locate and Identify wire fittings
Step 2. Running Network/Cat Cable connection
Step 3. Tighten Network/Cat Cable fitting
Step 4. Terminate Network/Cat Cable
Step 5. Test Network/Cat cable
Step 6. Connecting Network Cable to Moxa
Step 7. Run power wires
Step 8. Insert power wires
3. Wiring to controller
Step 1. Run cables from controller to Integration enclosure
Step 2. Insert Common Jumper strip
Step 3. Follow diagram to connect relays to controller
Advertisement
Related Manuals for Washify MOXA
Summary of Contents for Washify MOXA
- Page 1 Step 2. Running Network/Cat Cable connection Step 3. Tighten Network/Cat Cable fitting Step 4. Terminate Network/Cat Cable Step 5. Test Network/Cat cable Step 6. Connecting Network Cable to Moxa Step 7. Run power wires Step 8. Insert power wires 3. Wiring to controller Step 1.
- Page 2 1. Easy access to 120VAC power to provide power for the enclosure. 2. Less than 100ft ethernet cable length between the enclosure and the Washify network hub. As well as avoiding running the ethernet cable near equipment that causes large levels or electrical noise (Electric Motors, Electric Pumps, Power Inverters).
- Page 3 Step 1.1. Mount Metal mounting fins onto the enclosure with provided bolts...
- Page 4 Step 1.2. Mount Box to wall using lag bolts or required hardware for wall type.
- Page 5 Step 1.3. Verify Mounting is flush and will not fall...
- Page 6 2.Providing power and a network connection Step 2.1. Locate and identify fittings for power and network cable (take note of integration wiring fitting as it will be needed later)
- Page 7 Step 2.2. Run a Cat5e or Cat6 cable from the network hub to the Integration box. Do not place the RJ45 plug on the cat cable until it has been run inside the fitting. Remove the cap of the fitting, run the cable through the cap then into the enclosure. Leave enough slack to be able to work comfortably crimping the RJ45 plug on the cable.
- Page 8 Step 2. 3. Once the cable is inside the box, screw the cap back on the fitting and tighten.
- Page 9 Step 2.4. Terminate the Cat cable into a RJ45 end. Make sure to follow T568B standard on both ends of the Cat cable. You can find the standard in the image below. Step 2.5. If a cable tester is available, test the cable to verify all pins are conducting properly.
- Page 10 Step 2.6. Insert the crimped RJ45 end into Port 1 on the Moxa box shown below...
- Page 12 Step 2.7. Run power wire/cables to the enclosure from a 120VAC power source. Follow the same instructions as step 2 and 3, but for the power fitting. (Recap: Remove cap from fitting, insert cables through the fitting cap, then through the fitting inside the enclosure.
- Page 13 Step 2.8. Insert power cables into power terminal blocks. Most AC power in the United States of America uses the color codes for the wires as follows: Black: Line White: Neutral Green: Ground...
- Page 14 This section will describe how to wire the integration box to your controller. Step 3.1. Run cables from your car wash equipment controllers to the washify integration enclosure. Insert the cables into the last fitting, following the same method of ethernet and power.
- Page 15 Step 3.2. Place Jumper strip in common terminal to jump all commons. Looking at the relay terminal strips. The middle row is the common terminals. Below the Wire spots is a slot where the terminal jumper strip slides in. Please Refer to the photo with the Jumper strip installed. This is important. If this item is not installed or is missing.
- Page 16 Step 3.3. Follow the diagram on the below. Each controller will vary on its connection’s points. The...
- Page 17 If you have questions, please call your Washify Onboarding agent and they will be able to assist you. Washify has diagrams for specific controllers that have been worked with in the past. Please ask your Washify Onboarding agent if one is available for your controller.