Related Manuals for RAYN Lyda
Summary of Contents for RAYN Lyda
- Page 1 Lyda System Lamp Head and LED Driver Installation and User Manual Part Number: 7431M1200 Rev: A Released: 2022-05...
- Page 2 For current and complete compliance and product information, view the available documentation at rayngrowingsystems.com. RAYN Growing Systems intends this document, whether printed or electronic, to be provided in its entirety.
-
Page 3: Table Of Contents
Table of Contents Overview Safety Lyda LED Driver Lyda Lamp Head System Overview Sample Systems Cabling System DMX Dimming 1-10 V Dimming Accessories Specifications Environment Weights and Dimensions Clearance Electrical LED Driver Lyda Lamp Head DMX Adapter Optical Heat Dissipation Radiant Flux... - Page 4 Before You Begin Installation Installation Install the Lyda Lamp Head Install the LED Driver Install the DMX Adapter Power Up Procedure Operation Maintenance and Serviceability Troubleshooting LED Driver Lyda Lamp Head Install Lens Lamp Head and LED Driver Installation and User Manual...
-
Page 5: Overview
Overview The Lyda System is comprised of a lamp head and a LED driver that is flexibly suited for horticultural and other commercial applications. The lamp head features solid-state, long-life LEDs in a bar style head that is equipped with the latest generation of 5000K sun spectrum or white plus deep red LEDs. -
Page 6: Safety
Safety Lyda products are intended for professional use only. Read the entire user manual before using this equipment. WARNING: RISK OF ELECTRIC SHOCK! Circuits that are installed without an accessible power disconnect device cannot be serviced or operated safely. AVERTISSEMENT : RISQUE DE DÉCHARGE ÉLECTRIQUE! Il est... -
Page 7: Lyda Lamp Head
Do not install the lamp head against walls or ceilings. Suspend the lamp head in free-air to • allow for proper convection cooling. The Lyda lamp head is suitable for damp locations. Prevent direct water flow on the lamp • head. Do not install any Lyda system component underneath the irrigation system. -
Page 8: System Overview
System Overview The Lyda lamp head ships complete with the LED driver and a lamp cable. A regional specific power cable is available for connection of the LED driver to the mains power. See Accessories page 7. Rotate Rotate clockwise counter-... -
Page 9: Sample Systems
Line (black or brown) Line (black or brown) Neutral (white or blue) Neutral (white or blue) Ground (green or green/yellow) Ground (green or green/yellow) Lyda System with 1-10 V Dimming Current sink controller 1-10 V provided by others Controller Power Cable*... -
Page 10: Cabling System
Connect the control cable between the LED driver auxiliary input and the 1-10 V controller. This connection allows the LED driver to power the DMX Adapter and passes the control signal to the Lyda lamp head for dimming control with 10% to 100% intensity and Off for an input signal below 0.5 V. -
Page 11: Accessories
Accessories Model Part Number Description L-PCEU W6688 Power Cable, Shuko CEE 7/7, 1.8 m (6 ft) length L-PCUK W6689 Power Cable, UK 13 A BS1363, 1.8 m (6 ft) length L-PCUS W6690 Power Cable, US NEMA 5-15P, 1.8 m (6 ft) length L-PCBEUS W6691 Power Cable, Bare Ends US Color Code, 1.8 m (6 ft) length L-PCBEIEC W6692... -
Page 12: Specifications
Includes mounting flange Clearance Lamp heads can be ganged together lengthwise, but do not install the Lyda lamp head • against walls or ceilings. Ensure a minimum clearance of 50 mm (2 in) between the lamp head and other objects such as other lights, the ceiling, or wall surface for proper cooling. -
Page 13: Electrical
The LED driver supports the following output products: one Lyda lamp head (~220 W, 60 VDC) • one DMX Adapter available from RAYN Growing Systems (see Accessories for ordering • information) or a 1-10 V dimming controller (by others) utilizing sink current (0.5 mA maximum). -
Page 14: Lyda Lamp Head
The DMX address is set remotely from a compatible RDM controller. Optical The Lyda lamp head features 120° beam angle as standard (no lens installed). A 60° medium beam spread lens is available for field-installation and a 120° flat lens is available in cases where additional protection is desired for the face of the lamp head. -
Page 15: Before You Begin Installation
Install the Lyda Lamp Head The Lyda lamp head can be mounted by suspension or by a mounting bracket in a horizontal (X) or vertical (Y) orientation using the end caps as the attachment points (mounting hardware not provided). - Page 16 3. If the LED driver has been previously installed, connect the lamp cable from the driver to the Lyda lamp head. The connection is secured by rotating the locking ring counterclockwise until finger tight. If the LED driver is not yet installed, see Install the LED Driver on the facing...
-
Page 17: Install The Led Driver
2. Connect the lamp cable from the LED driver to the installed Lyda to connect lamp head. The connection is secured by rotating the locking ring counterclockwise until finger tight. 3. Connect the control cable (optional use for 1-10 V dimming control). -
Page 18: Install The Dmx Adapter
One for DMX In (pin-style connector) and one for DMX Thru (socket-style connector). Make the connections accordingly. See Lyda System with DMX Dimming on page 5 for example system topology. Contact your RAYN Growing Systems provider for additional system design guidance. Note: The XLR connectors provided are factory terminated as follows:... -
Page 19: Power Up Procedure
If no external control (DMX Adapter or third-party 1-10 V controller are installed, the Lyda • lamp head will illuminate to 100% output. If external control is installed, the Lyda lamp head will illuminate to the output level • signaled by the controller. Set the appropriate control level on the controller and verify the respective light output. -
Page 20: Maintenance And Serviceability
LEDs on the lamp head are cleaned regularly from dirt and dust using a lint-free cloth. The Lyda lamp head, LED driver, and the DMX Adapter (if used) are not user serviceable. Note: Do not attempt a repair. Instead, contact your RAYN Growing Systems provider for further assistance. -
Page 21: Install Lens
It is best accomplished on a flat work surface with all power and cables disconnected. 1. Disconnect power to the LED driver and disconnect the Lyda lamp head cable from the LED Driver. - Page 22 Lamp Head and LED Driver Installation and User Manual...
- Page 23 Install Lens...
- Page 24 RAYN Growing Systems 3031 Pleasant View Rd, PO Box 620979, Middleton WI 53562 0979 | +1 844 907 RAYN © 2022 RAYN Growing Systems, LLC. | All Rights Reserved. Trademark and patent info: rayngrowingsystems.com/ip All product information and specifications subject to change.
Need help?
Do you have a question about the Lyda and is the answer not in the manual?
Questions and answers