Related Manuals for Massive Dimension MDPE10
Summary of Contents for Massive Dimension MDPE10
- Page 1 Massive Dimension Vermont, USA, Earth 1-802-505-6772 Massive Dimension MDPE10 Extruder Operation Manual This manual applies to the Massive Dimension MDPE10. Triex LLC, Barre, VT 05641, USA REV. 1 2-16-2021...
- Page 3 TOXIC FUMES Some plastics such as PVC can produce ● dangerously toxic fumes when they are heated. Always carefully review the MSDS of any material before using it in the MDPE10 to avoid dangers to your health. Always use the MDPE10 in a well- ventilated area.
-
Page 4: General Specifications
General Specifications Thermal Power Input: 208~240VAC-4.8A 50/60Hz 1-Phase 1000W MAX - varies with settings Weight: 13.8kg (30.5 lbs) - With Servo & Gearbox 7.85kg (17.3 lbs) - Without Servo and Gearbox Dimensions: 27.8cm D x 20.3cm W x 54.2cm H (10.9in L x 8.0in W x 21.3in H) Refer to “MDPE10_Public_Dimensions”... -
Page 5: Parts Included
Parts Included... - Page 6 Parts Included cont. EX6-625 Extrusion Screw 5/8” OD 2:1 Comp Brass Bristle Tube Cleaner Tube Cleaner Extension Rod High-Temperature Resistant Terry Cloth Gloves Copper Gauze Brass Bristle Wheel (4x) MD Nozzle 1.5mm Magnetic Screw Retainer Rod 1-1/8” Mini-change 9-pole cord set 12’ long (AMX10E0010) 10.
- Page 7 Thermal Control Components Refer to “MDPE10 Wiring Diagram” for thermal control wiring Temperature Control PIDs Automation Direct Part # SLB4848-V0 Mount these PIDs in a controls enclosure with 1/16 DIN panel cutouts. Run the auto-tuning function (page 5-2 of the PID manual) at the set temperature you plan to operate the machine at.
- Page 8 Servo Motor & Servo Drive Components Servo Drive Automation Direct Part # SVA-2100 Refer to the SureServo manual to set up the drive parameters for your implementation: https://cdn.automationdirect.com/static/manuals/sureservomanual/surese rvomanual.html A serial programming cable is provided (AD Part # SVC-PCCFG-CBL). Connect the drive to a PC’s 9-pin D-sub serial port to set and load drive parameters using the SureServo PRO Software which can be downloaded here: https://support.automationdirect.com/products/sureservo.html The servo drive I/O is broken out by the...
- Page 9 Installing the Screw 1. Apply a very thin layer of grease to all 5 flat surfaces of the square tang on the back of the screw. Be careful not to leave excess grease on the edges of the tang to minimize grease getting on the barrel walls while inserting the screw.
- Page 10 Cleaning Caution! Parts of the extruder get hot! Wear gloves and eye protection! It is recommended to thoroughly clean the extruder after use, or right before the next use, for the most consistent extrusion. Polymer melt on the screw due to heat creep after shutdown can cause issues when restarting the extruder.
- Page 11 Cleaning - Continued 6. Pull the screw the rest of the way out of the barrel using gloves, then clamp the back of the screw in a non-marring vice with a v-block for cleaning. NOTE: Clean the screw while it is still hot. Always use a smooth, non-marring vice and v-block to secure the screw.
- Page 12 Triex LLC. This manual applies only to the Massive Dimension MDPE10. While Triex LLC has applied all possible caution in producing this manual, we urge the customer or user of this device to contact Triex LLC with any questions or concerns about operation, before operating the device or making any adjustments.
Need help?
Do you have a question about the MDPE10 and is the answer not in the manual?
Questions and answers