Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for baracuda 0327405
Summary of Contents for baracuda 0327405
- Page 1 HYDRA+ SINGLE SPEED Installation & Operating Instructions...
-
Page 2: Table Of Contents
Routine Maintenance ........10 General Maintenance Information ....10 Refer to the following websites for information on warranty and service in your country: • Australia, NZ, Asia and South Pacific go to www.baracuda.com.au EQUIPMENT INFORMATION RECORD Date of Installation ____________________ Installer Information _____________________________________________________________... -
Page 3: Section 1. Important Safety Instructions
These requirements are generally not intended to apply to the pool equipment, such as filters or pumps. Baracuda pool equipment is pressure tested at the factory. If, however, the WARNING cannot be followed, pressure testing of the piping system must include the filter and/or pump. - Page 4 • Water temperature for test must NOT EXCEED 35°C (95°F). • Limit test to 24 hours. After test, visually check system to be sure it is ready for operation. NOTICE: These parameters apply to Baracuda equipment only. For non-Baracuda equipment, consult the equipment manufacturer.
- Page 5 Baracuda® Hydra+ Single Speed | Installation and Operating Instructions WARNING The following guidelines provide information for pump installation that minimizes risk of injury to users of pools, spas, and hot tubs: Entrapment Protection - The pump suction system must provide protection against the hazards of suction entrapment.
- Page 6 • The distribution or modification of this document in any way is prohibited, without prior authorisation from Baracuda. • Baracuda is constantly developing its products to improve their quality. The information contained herein may therefore be modified without notice. WARNING •...
-
Page 7: Section 2. Installation
• This appliance is compatible with all types of water treatment used in swimming pools. Refer to the Baracuda warranty conditions for details of the permitted water balance values. • Never run the pump dry or out of the water as this will void the warranty. -
Page 8: Electrical Connection
Baracuda® Hydra+ Single Speed | Installation and Operating Instructions Section 3. Operation • Check that the hydraulic corrections are correctly tightened and that there are no leaks. WARNING • The pipes must be supported to prevent NEVER run pump dry! Running pump dry may... -
Page 9: Priming The Pump
Baracuda® Hydra+ Single Speed | Installation and Operating Instructions • Check that the pump is stable and level. • The hydraulic circuit must be bled and not contain any foreign bodies. • The pump pre-filter strainer cover must be correctly closed (by hand) and its gasket clean and in place. -
Page 10: Section 4. Maintenance
Baracuda® Hydra+ Single Speed | Installation and Operating Instructions Section 4. Maintenance General Maintenance Information • All other work must be performed by a WARNING qualified person. • In the interest of safety and reliability, only Switch the pump off before doing any maintenance, cleaning or other work. -
Page 11: Winterising
Baracuda® Hydra+ Single Speed | Installation and Operating Instructions Servicing These include: • Damage to the motor, due to untimely or WARNING inadequate maintenance or cleaning of the cooling fan cover. It is recommended that the appliance undergo general servicing at least on a yearly basis to •... -
Page 12: Section 6. Troubleshooting
Baracuda® Hydra+ Single Speed | Installation and Operating Instructions Section 6. Troubleshooting • If a problem occurs, before you contact your retailer, please carry out these few simple checks using the following tables. • If the problem continues, contact your retailer. -
Page 13: Section 7. Pump Parts
Pump Footpiece Assembly NOTE: For any further enquiries or troubleshooting advice, please contact your local authorised Baracuda dealer. Alternatively contact Baracuda customer service on 1300 784 423 or www.baracuda.com.au An electronic copy of this manual may be found on www.baracuda.com.au... - Page 14 Record your equipment details here for quick reference: Model No. : _______________________________________ Serial No. : _______________________________________ Baracuda is a registered trademark of Fluidra Group Australia Pty Ltd ABN 87 002 641 965 219 Woodpark Rd, Smithfield, NSW 2164 Australia Tel: 1300 784 423 www.baracuda.com.au...
Need help?
Do you have a question about the 0327405 and is the answer not in the manual?
Questions and answers