ISkin Cerulean F1 User Manual

Using the Controls Page 5
To: Do this:

CERULEAN F1 Headset Controls

Redial Last Number * Press and Hold the Multi-function button until beep Press / Hold / Release
Activate Voice Dial *
Press the Multi-function button Press / Release
Answer Incoming Call Press the Multi-function button
Press / Release
Reject Incoming Call * Press and Hold the Multi-function button until beep on incoming call Press / Hold / Release
Terminate Current Call Press the Multi-function button during call Press / Release
Mute Mic ON/OFF Press either the Next or Prev Track button
Press / Release
Cancel outgoing call
Press and Hold the Multi-function during outgoing call
Press / Release
Transfer call to/from phone * Press the Multi-function button during call until beep
Press / Hold / Release
Call Waiting Press and Hold the Next/Prev Track button during first call until beep
* Press / Hold / Release
(answer second incoming call)
Toggle between Calls
* Press and Hold the Next/Prev Track button during call until beep Press / Hold / Release
Multi-function Button Next/Prev Track Button
The above functions require a device with HFP and HSP Bluetooth support (refer to your device's manual). *Dependent on mobile phone features.
CERULEAN F1 Remote Control Functions (AVRCP)
To: Do this:
Play/Pause
Press the Multi-function button once for each command Press / Release
Stop playing
Press and Hold Multi-function button until music stops
Press / Hold / Release
Skip to next track Press the Next Track button
Press / Release
Skip to previous track
Press the Prev. Track button
Press / Release
The F1's volume controls affect only the F1 and does not remotely
Control volume
control the volume of a connected device.
Press either the "+" or "-" on the Volume Control button Press / Release
Control volume Up/Down
Multi-function Button Next/Prev Track Button Volume up/down
The above functions require an iPod equipped with the CERULEAN TX Bluetooth transmitter or a device with AVRCP Bluetooth
support (See your device's manual. Compatibility may vary).
What's Inside the Box Page 1
L
R
CERULEAN F1 User's Guide Additional
USB Charging Cable
Stereo Bluetooth Earphones Warranty Info Ear hooks
Type A to Mini-A 4 pin
with Headset functionality.
Front Bottom Top

Switches and Controls

Side
(Right Earpiece)
The RIGHT earpiece contains all controls
including the power switch.
The LEFT earpiece contains the lithium Mic
battery.
Multi-function Speaker
Button
Volume
Controls Mini USB
Next/Prev Power
Defualt Status LED
Port (Type A) Track ON/OFF
Light
Ear Hook
The CERULEAN F1 is both a stereo Bluetooth® earphone and a mono headset. As a stereo earphone, you can
connect to a stereo Bluetooth (A2DP) audio device or iPod® (equipped with the * CERULEAN TX) and listen to
your audio wirelessly. As a mono headset, you can connect to a Bluetooth mobile phone, accept or reject calls
and access other call features.
* CERULEAN TX Bluetooth® Transmitter (sold separately)
The CERULEAN F1 uses standard Bluetooth 2.0 defined profiles making it capable of interacting with other
Bluetooth devices. These profiles allow it to remotely control specific features of a device, act as wireless
stereo earphones and also act as a wireless mono headset for a mobile phone.
Supported Profiles.
A2DP Enables the CERULEAN F1 to receive stereo audio wirelessly from any (A2DP) Bluetooth device.
AVRCP Enables the CERULEAN F1 to remotely control specific features of any (A2DP) Bluetooth device.
Enables the CERULEAN F1 to act as a wireless mono headset for taking phone calls via a Bluetooth mobile phone.
HSP
HFP Enables the CERULEAN F1 to remotely make, answer or terminate a call on a Bluetooth mobile phone.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by iSkin Inc. is under license.
iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
Using the Controls continued.. Page 6
To: Do this:

CERULEAN F1 Power and Pairing Controls

Turn power on/off: Slide the ON/OFF switch to the desired position
PRESS and Hold the Multi-function button
Make discoverable
+
then slide ON/OFF switch to ON position
(enter pairing mode)
Make undiscoverable
PRESS the Multi-function button once
(exit pairing mode)
Set the ON/OFF switch to the ON position and Press and Release
Reconnect to paired device +
the Multi-function button once. Must be initially paired with a device.
Multi-function Button ON/OFF Switch
Specifications

Product Specifications

General: Earphone Driver Unit:
Diameter <15mm
Bluetooth version 2.0, Class II
Frequency Response 20Hz ~ 20KHz
Bluetooth Profile Support A2DP / AVRCP / HSP/ HFP
Sound Pressure Level 93dB @ 1KHz
RF Frequency 2.4GHz / 79 Channel / AFH Impedance 16 @ 1V, 1KHz
Power Rating 5mW (Max)
Operational Range Standard 33 feet (10 meters) *
Talk Time (Headset ) max.10 hours *
Other:
Music Listening (Earphone) max. 8 hours *
Microphone Typical : ECM unit
(110dB)
Standby Time up to 300 hours
S/N Ratio Up to 58dB
Battery Charge Time 2.5 hours (Lithium-Polymer)
Dimensions 47 25 23.5
mm x mm x mm
Power / Charging Method (USB) 5V, 300mA / DC
(L) x (W) x (H)
Weight 35g (approx.)
* May vary depending on user habits.
Warning
A headset that covers both ears may impair your ability to hear environmental sounds. Use
of this headset while operating a motor vehicle or riding a bicycle may pose a serious hazard
to your personal safety and is not recommended.

Getting Started

Page 2

Charging the Battery:

It is recommended that the CERULEAN F1's battery be charged for at least 6 hours
prior to first use; however, subsequent charges require only 2-3 hours to fully charge.
USB AC Power Adapter
Mac / PC OR
Output: 5V(DC)
(sold separately)
USB
Using the included USB charging cable, plug the smaller end of the cable into the
CERULEAN F1 USB port and the wider end into the USB port on your computer. The
following chart describes battery status indicated by the Status LED light located in
the centre of the Multi-function button.
Status Light Colour Status / Description
ON BLUE Battery charging in progress
ON WHITE Battery charging complete
Low battery indicator. Charging required. In addition, a low battery
FLASHING BLUE
sound will alert you when recharging is necessary (3% or below).
Note: Longer distances between paired devices and higher volume levels impact battery performance.
To conserve battery life, turn the power off when not in use.

Wearing the CERULEAN F1

Correct ear hook
Following the diagram, install the CERULEAN F1
position
over each ear and ensure the right (R) and left (L)
earpieces are correctly placed. Adjust to ensure
it is secure and fitted comfortably.
Swapping Ear Hooks
Included with the CERULEAN F1 is an additional
pair of ear hooks. These ear hooks feature a different
Right earpiece contains all
design and may offer a better fit.
controls and microphone.
Note: When removing ear hooks, be sure to firmly hold the CERULEAN F1 securely and carefully
snap off the hook from the base. Snap replacement ear hooks over the base while ensuring
they are facing the correct direction (see diagram above).

Troubleshooting

Page 7
The Status LED on my CERULEAN F1 is not on or flashing.
Check that the CERULEAN F1 is powered on. If the power is on but the LED is off, then try
charging the unit as described in this manual.
Crackling noises and/or interruptions when listening to the CERULEAN F1.
Bluetooth is a radio technology. It is sensitive to environmental conditions and
objects that may interrupt the signal. Cordless phones, wireless internet routers or
any device that operates on wireless frequency of 2.4GHz may cause some interference.
To ensure clear sound, use the device within the operational range and conditions
specified in this manual.
Difficulty pairing the CERULEAN F1 with a Bluetooth device.
Make certain that the device you are attempting to connect to is compatible with the
Bluetooth profiles supported by the CERULEAN F1. Check that the CERULEAN F1
is set to discover mode as explained in this manual. Make sure there are no other
Bluetooth devices that may be attempting to pair with the CERULEAN F1.
No sound can be heard from the CERULEAN F1.
Verify that the CERULEAN F1 is properly paired with the correct Bluetooth device
and that the device is set to and capable of outputting audio to the CERULEAN F1.
Check the volume levels on both the connected device and the CERULEAN F1.
Other questions? Learn more about Bluetooth and the CERULEAN TX/RX
at www.iSkin.com
Warranty Service
Note: The Serial Number is located in fine print on the inside of the RIGHT (R) ear piece.
If the CERULEAN F1 does not seem to function correctly, consult the Troubleshooting
section of this guide and/or visit iSkin.com for further online resources. If the unit
continues to malfunction, visit iSkin.com and check the warranty section for infromation.

Pairing the CERULEAN F1 to a Stereo Bluetooth Device

Page 3
Make the CERULEAN F1 discoverable:
Making the CERULEAN F1 discoverable allows other Bluetooth devices to find and pair with it.
1. Make sure the CERULEAN F1's power switch is in the OFF position.
2. PRESS and HOLD down the CERULEAN F1's Multi-function button and SWITCH the power ON.
3. The Status LED light on the CERULEAN F1 will alternate BLUE/WHITE when made discoverable.
The CERULEAN F1 is now ready to be paired with another Bluetooth device.
Note: The CERULEAN F1
+ =
will remain discoverable for
approximately 3 minutes.
PRESS and HOLD SWITCH Flashing Light
(Multi-function button) the power ON BLUE/WHITE
(discoverable)
Pairing the CERULEAN F1 with Your Bluetooth Device
(Mobile Phone, PDA, ...etc.)
1. Make sure Bluetooth is enabled on your device.
Refer to your device's manual for Pairing with a Bluetooth headset.
2. Select the "Search for Bluetooth Device" (or similar) option on your device.
3. Choose the iSkin CERULEAN F1 from the list of found devices.
4. To complete the pairing process, you will be prompted to enter
a security code. Enter 0000 (four zeros) and continue.
Note: If pairing fails, refer to the Troubleshooting section of this guide and/or repeat the
above steps.
F1 F1
User's Guide
F1
iSkin and CERULEAN are trademarks of iSkin Inc.,
registered in Canada, the U.S. and other countries.
Printed in China
www.iSkin.com

Reconnecting the CERULEAN F1 to the Previously Paired Device

Page 4
1. Switch the Power ON.
2. Press and release the Multi-function button once.
The status LED light on the CERULEAN F1 will begin to flash rapidly indicating that it is
seeking the last device it was paired with (make sure the previously paired device is
available and turned on). If you try to pair the CERULEAN F1 with a new device, it is
necessary to make the CERULEAN F1 discoverable
(See Page 3).
Pairing the CERULEAN F1 with a CERULEAN TX (Sold Separately) Equipped iPod
You can pair the CERULEAN F1 with a CERULEAN TX equipped iPod to wirelessly listen to
music and remotely control features of the iPod.
1. Make the CERULEAN F1 discoverable (See Page 3).
2. Plug the CERULEAN TX into your iPod (TX will enter pairing mode).
3. The CERULEAN TX status LED light will begin to flash rapidly and automatically pair with
the F1 within 20 seconds.
4. The status LED light on both the CERULEAN TX and F1 will flash slowly when successfully
paired. (See CERULEAN F1 Control Functions on Page 5.)
Multi-point Pairing (Pair CERULEAN TX With iPod and Mobile Phone Together)
You can pair both your mobile phone and the CERULEAN TX equipped iPod with the
CERULEAN F1 to listen to your music and accept incoming phone calls.
1. Pair the CERULEAN F1 with your mobile phone.
2. Pair the CERULEAN F1 with your TX equipped iPod (doing so will temporarily disconnect
your mobile phone).
3. Using your mobile phone's Bluetooth menu, select the previously paired iSkin CERULEAN
F1 as a headset device.
Note: While listening to music from the TX equipped iPod, the F1 is in stereo earphone mode and may be
used to control the iPod. Upon an incoming phone call, the F1 will switch to mono headset mode and
may be used to control your mobile phone. After terminating a phone call, the F1 returns to stereo
earphone mode and resumes music playback.