Omron Q2A-A Series Installation & Operation Instructions page 138

6 Attachments
Model Terminals
R/L1, S/L2, T/L3
U/T1, V/T2, W/T3
-, +1
4296
+3
R/L1, S/L2, T/L3
U/T1, V/T2, W/T3
-, +1
4371
+3
R/L1, S/L2, T/L3
U/T1, V/T2, W/T3
-, +1
4389
+3
R/L1, S/L2, T/L3
R1/L11, S1/L21, T1/L31
U/T1, V/T2, W/T3
4453 -, +1
+3
R/L1, S/L2, T/L3
R1/L11, S1/L21, T1/L31
U/T1, V/T2, W/T3
4568
-, +1
4675
+3
*1 For IP20 protection, use wires that are in the range of applicable gauges. If your installation does not need IP20 protection, smaller
cables can be used.
*2 Remove insulation from the ends of wires to expose the length of wire shown.
*3 For wire gauges more than 30 mm
*4 Install an RCM/RCD with this wire gauge to maintain compliance with IEC/EN 61800-5-1:2007.
*5 Terminals - and +1 have two screws. The Recommended Gauge is the wire gauge for one terminal.
*6 A junction terminal is necessary to connect a braking resistor unit (LKEB-series) to terminals B1 and B2.
138
Applicable Gauge
Recommended Gauge
2
mm
(AWG kcmil)
70 × 2P
(3/0 × 2P)
95 × 2P
(4/0 × 2P)
70 × 2P
(1/0 × 2P)
95
(2)
120 × 2P
(250 × 2P)
120 × 2P
(250 × 2P)
70 × 2P
(3/0 × 2P)
120
(1)
120 × 2P
(300 × 2P)
120 × 2P
(400 × 2P)
95 × 2P
(4/0 × 2P)
95
(1)
120 × 4P
(250 × 4P)
95 × 4P
(4/0 × 4P)
95 × 4P
(4/0 × 4P)
70 × 4P
(3/0 × 4P)
150
(1/0)
120 × 4P
(250 × 4P)
95 × 4P
(4/0 × 4P)
95 × 4P
(300 × 4P)
70 × 4P
(3/0 × 4P)
95 × 2P
(2/0)
2
, tighten to a tightening torque of 4.1 N∙m to 4.5 N∙m (36 lb.∙in. to 40 lb.∙in.).
Wire Stripping
*2
Length
*1
IP20
2
mm
mm
(AWG kcmil)
70 - 95 × 2P
-
(2/0 - 4/0 × 2P)
120 × 2P
-
(4/0 - 250 × 2P)
70 × 2P
-
(1/0 × 2P)
95 - 240
-
(2 - 350)
150 × 2P
-
(250 - 300 × 2P)
185 × 2P
-
(300 - 400 × 2P)
50 - 95 × 2P
-
(1 - 4/0 × 2P)
120 - 240
-
(1 - 350)
150 × 2P
-
(250 - 300 × 2P)
185 × 2P
-
(300 - 400 × 2P)
50 - 95 × 2P
-
(1 - 4/0 × 2P)
35 - 240
-
(1 - 350 × 2P)
150 × 4P
-
(250 - 300 × 4P)
120 - 150 × 4P
-
(250 - 300 × 4P)
185 × 4P
-
(300 - 400 × 4P)
95 × 4P
-
(4/0 × 4P)
50 - 150
-
(1/0 - 300)
150 × 4P
-
(250 - 300 × 4P)
120 - 150 × 4P
-
(250 - 300 × 4P)
185 × 4P
-
(300 - 300 × 4P)
95 × 4P
-
(4/0 × 4P)
60 - 150
-
(2/0 - 300)
TOMPYEUOQ2A03C AC Drive Q2A Installation and Operation Instructions
Tightening Torque
Terminal
Screw
N∙m (lb.∙in.)
20
(177)
M10
20
(177)
M10
20
(177)
M10
18 - 23
(159 - 204)
M10
35
(310)
M12
35
(310)
M12
35
(310)
M12
32 - 40
(283 - 354)
M12
35
(310)
M12
35
(310)
M12
35
(310)
M12
32 - 40
(283 - 354)
M12
35
(310)
M12
35
(310)
M12
35
(310)
M12
35
(310)
M12
32 - 40
(283 - 354)
M12
35
(310)
M12
35
(310)
M12
35
(310)
M12
35
(310)
M12
32 - 40
(283 - 354)
M12