Subscribe to Our Youtube Channel
Related Manuals for PowerWalker PDU for VFI ICRS IoT 10kVA 3-1
Summary of Contents for PowerWalker PDU for VFI ICRS IoT 10kVA 3-1
- Page 1 PDU for VFI ICR IoT 6-10kVA Installation and user manual Service and support: Call your local service representative...
- Page 2 . his manual contains important instructions that should be followed during installation and maintenance of the MBP. The MBP models that are covered in this manual are intended for installation in an environment within 0 to 50°C, free of conductive contaminant. pecial s mbols serve the warnin associated with the ris of electric shoc s m ol.
- Page 3 afet of persons Terminal blocks may be energized even if the system is disconnected from the AC power source. Dangerous voltage levels are present within the system. It should be opened exclusively by qualified service personnel. The system must be properly grounded, always connect the earth wire first. ...
-
Page 4: Table Of Contents
CONTENTS 1 Introduction ....................1 1.1 Environmental protection ................1 2 Product Overview ................... 2 2.1 Model list ....................... 2 2.2 Presentation ....................2 3 Installation ....................4 3.1 Unpacking and Inspecting................4 3.2 Checking the accessory kit ................4 3.3 Mechanical Installation .................. -
Page 5: Introduction
1 Introduction Thank you for selecting MBP(Maintenance Bypass modular) to protect your electrical equipment. The MBP allows service person to service or replace the UPS without interrupting the connected loads. Besides, it also allow you apply for below extension used Terminal block connection design enable the MBP connect to other type UPS. -
Page 6: Product Overview
2 Product Overview ode i t 1. The weight in this table is reference only, please see the labels on the carton for details. . Dimension ‘D’ is chassis only. roduct et Weights (kg) Dimensions (mm) W PDU for VFI ICR IoT 6-10kVA 1-1 PDU for VFI ICRS IoT 10kVA 3-1 2 2 Pre e t tio... - Page 7 ear anel utput socket group (programmable) aintenance bypass switch nput utput terminal ( onnected to power and load) nput switch port(including E Detect and T model nput utput terminal ( onnected to ront anel ear anel...
-
Page 8: Installation
The system may be installed only by qualified electricians in accordance with applicable safety regulations. ecti npacking the unit in a low-temperature environment may cause condensation occurred in and on the cabinet. Do not install the unit until the inside and outside of the unit are absolutely dry (ha ard of electric shock). -
Page 9: Mechanical Installation
is odel support installation odes ac installation and o er installation t is reco ended to connect ca les for S nput Output and detection ca le to t e efore installing e o e t e co er of ter inal loc s and connect ca les for S nput Output to ter inal loc s refer to t e indication on rear panel or ca les... - Page 10 ssu e t at ou alread purc ased our S and fi t e S in to er position S pro ided positions to install t e , needed additional space is as t is reco ended to select eft position as our final installation according to t e configured lengt of ca les for S nput Output and detection ca le...
- Page 11 osition ear of rac • osition ront of rac • nstall ail it to rac ca inet scre s and as ers...
-
Page 12: Power Cables Connection
Slide into rail it and a e sure loc t e clips is c apter introduces o to connect S, and connect ca le to efore po er ca les connected, nsert detection ca le to t e port on t e rear of... - Page 13 onnect ca les for S nput Output to S ter inal loc s refer to indication - m d - m d AC C lease refer to S user anual for upstrea protection and do nstrea s itc ended ca le ini u cross-sectional area odel K S - 0K S -...
- Page 14 ig lea age current art connection essential efore connecting suppl is t pe of connection ust e carried out qualified electrical personnel efore carr ing out an connection, c ec t at t e upstrea protection de ices Nor al source are open O Off e o e t e co er of ter inal loc onnect t e...
- Page 15 is odel support ode setting as elo , default is setting it 3- S ort input ter inal us ar , t en connect ca le or ca les ell fi ed, it is reco ended to tie t ese ca les to t e con e of rear-panel 3 nstall ac t e co er of ter inal loc...
-
Page 16: Service Operation
lease a e sure t e S is turned to pass ode efore rotating t e aintenance s itc to pass position e o e t e aintenance s itc co er , t e ill turn to pass auto aticall otate t e aintenance s itc to SS position Note... -
Page 17: How To Disconnect Cables Between Mbp And Ups
is is to disconnect ca les for S nput Output and detection ca le e pictures as elo are e a ples of ac position onl nloc t e clips and pull out its position s oot l , t en rotate t e as elo isconnecting ca les for S nput Output and... -
Page 18: How To Detect The Ebm To This System
is is to connect t e configured to a s ste detection ca le as elo... -
Page 19: Specifications
lectrical input—refer to t e S input specification lectrical output—refer to t e S output specification Nor al output 0 & Output soc et group rogra a le output 0 & Outlet soc et group rogra a le can e set on t e sending co and;...
Need help?
Do you have a question about the PDU for VFI ICRS IoT 10kVA 3-1 and is the answer not in the manual?
Questions and answers