Black & Decker BDCDS18 Original Instructions Manual page 9

Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot or
too cold, it automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery pack has reached an
appropriate temperature. The charger then automatically
switches to the pack charging mode. This feature ensures
maximum battery pack life. A cold battery pack will charge at a
slower rate than a warm battery pack. The pack will charge at
that slower rate throughout the entire charging cycle and will
not return to maximum charge rate even if the pack warms.
Installing and removing the battery pack from
the tool
To install battery pack (Fig. C)
Insert battery (5) into tool foot until an audible click is heard
(Figure. C)
Ensure battery pack is fully seated and fully latched
into position.
To remove battery pack (Fig.D)
Depress the battery release button (5a) as shown in figure D
and pull battery pack (5) out of tool foot.
@
Assembly
Warning! Before assembly, make sure that the tool is
switched off and the battery is removed.
Fitting sanding mesh (Fig. E)
Hold the tool with the sanding base facing upwards.
Place the sanding mesh (7) onto the sanding base, making
sure that the holes in the sheet line up with the holes in
the base.
Fitting sanding sheets (Fig. F - Optional accessory)
Detach the two additional diamond-shaped tips (9) from the
sanding sheet (8).
The diamond-shaped tip (9) can be reversed and replaced
when worn.
When the front part of the tip (9) is worn, detach it from the
sheet, reverse it and press it onto the sanding base again.
When the whole tip is worn, remove it from the sanding base
and fit a new tip.
For optimal dust collection, ensure the correct type of sanding
paper is used.
Finger attachment (Fig. G)
The finger attachment is used for fine detail sanding.
Remove the screw (11).
Remove the diamond-shaped tip (10) from the sanding base.
Fit the finger attachment (4) onto the sanding base.
Fit and tighten the screw (11).
Fit the appropriate sanding sheet onto the finger attachment.
Replacing diamomnd shaped tip (Fig. G1)
Replace the diamond shaped tip (10).
Replace and tighten screw (11).
Fitting and removing the dust cassette (Fig. H)
Slide the dust cassette (2) onto the connector (2a) and make
sure that it is securely located.
To remove the dust casette, pull it to the rear and away from
(original instructions)
the rear end of the tool.
Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off
To switch the tool on, depress the on/off switch (1) at the
forward position I.
To switch the tool off, depress the on/off switch (1) at the
back position O.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
@
regular cleaning.
WARNING! Before performing any maintenance
on the tool, remove the battery from the tool.
Unplug the charger before cleaning it.
Regularly clean the ventilation slots in your tool and charger
using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com
Technical data
Input voltage
Oscillations (no load)
Orbits (no load)
Sanding base surface
Weight
English
BDCDS18
V 18
dc
min 12000
-1
min 12000
-1
mm 8866
2
kg 0.85
9