Quoizel QR3326 Assembly Instruction Sheet

Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, gloves, safety glasses.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the mirror. Contact customer service for replacement
parts.
Warnings and Cautions
These instructions are provided for your safety. It is very important you read them completely before installing the mirror. We strongly
recommend that a licensed, professional electrician perform the installation. Quoizel recommends 2 people for each step during assembly.
Package Contents
Mirror Hanger
A
x 2
Hanger Nail
B
x 4
NOTE: There are two options (Templates or Measurement) for
identifying correct locations for Nails.
-
Option A Identify Nail Points for mounting the Mirror Hangers
By Using Template
The template included with package is provided to assist you in placing
the mirror in the location you desire. The template is a full size drawing
of your mirror and includes hanger mounting locations that your mirror
maybe hung.
Place the template on the wall in the location you have selected for
your mirror. Once you have the template in the location you desire and
making sure it is level you may tape or pin the template to the wall. Now
you may mark the holes for the mounting hardware as indicated on
your template. You may mark the mounting hardware location by either
using a pin and pushing it through the template leaving a small hole on
the wall. Or you may use a pencil and place a mark on the wall through
a small hole you cut into the template at the correct mounting location.
Remove the template from the wall and install the Mirror Hangers as
described in Step 1.
Mark Nail Locations
On The Wall At
Arrow Locations
6.25"
2" 17.75"
TEMPLATE
VERTICAL
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
2017 QuoizelInc.
Assembly Instruction Sheet #IS-QR3326
for product cleaning tips. Go to the
20-30 minutes
Mark Nail Locations
6.25" On The Wall At
Arrow Locations
4.25"
2"
2" 24"
TEMPLATE
HORIZONTAL
Figure A
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
For Styles QR3326 and QR3327
Care + Maintenance selection.
Mirror
C
x 1
VERTICAL
-
Option B Identify the Points for mounting the Mirror Hangers By
Using Measurement
A. Determine where the mirror will be placed on the wall and hold the
mirror on the wall in the position you wish. Mark the wall at the
bottom center of the mirror with a pencil lightly. This will be
Measurement A, the distance from the floor to the bottom of the
mirror.
B. Place the mirror on a flat surface again and measure from the
bottom of the mirror to the hangers that will be used to hang the
mirror, this is measurement B.
C. Add measurement A from step A above and measurement B together
and mark this spot on the wall where the mirror will be hung.
Measurement B is straight up from Measurement A you marked on
the wall in step A above.
D. Measure the distance between the centerline of each hanger and
then divide this measurement by 2, this is Measurement C. In order
to locate the exact hanger location on the wall, from Measurement B
go to the right the distance of Measurement C and mark the wall. Do
this going to the left of Measurement B as well and mark the wall.
These two marks are the center of the hangers, Measurement C.
The two marks you just made on the wall are the same distance
apart as the two hangers.
E. (Refer Figure B2) To determine
where the Mirror Hangers (A)
will be fastened to the wall,
measure up from Measurement
C 3". Do this in two locations as
4.25"
illustrated and mark the wall.
F. Refer to Step 1 to install Mirror
Hangers on the wall.
2"
-
STEP 1 Installing the 2 Mirror Hangers
A. Using the Nails (B) provided with the Mirror Hangers (A) attach the 2
Mirror Hangers (A) to the wall at the position just marked by Option A
or Option B. Please note the Mirror Hangers are adjustable
allowing for easy leveling of the mirror as needed.
B. Once you have both Mirror Hangers (A) securely nailed in place,
1of2
Hanger
" C"
BACK
" A"
Floor Surface
OPTIONAL B
Figure B1
Mirror Hanger
Figure B2
Hanger
" C"
BACK
"A"
C
3"
C
Mark "B"
Hook
ReleasedDate:2017-09-13