Page 2
SCHNEIDER ELECTRONICS GMBH-GERMANY 1. CAUTION CA UTION: Use of controls, adjustments or procedures other than those specified herein may result in hazardous radiation exposure. CA UT ION : T O RE DUCE TH E RIS K OF CA U T ION ELECTR ICA L SHOCK, DO NOT RE MOVE COVER (OR BACK).
Page 3
SCHNEIDER ELECTRONICS GMBH-GERMANY IMPORTANT SAFETY INSTRUCTIONS CAUTION: Read all of these instructions. Sa ve these instructions for later use . Follo w all W arnings and Instructions marked on the audio equipment. 1. Read Instructions-All the safety and operating instructionsshouldbe read before the productis operated. 2.
Page 4
SCHNEIDER ELECTRONICS GMBH-GERMANY PROTECTION AND LOCATION OF YOUR SET Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall outlet and refer servicing to qualified service personnel.
Page 5
SCHNEIDER ELECTRONICS GMBH-GERMANY OPERATION OF YOUR SET 18. This television set should be operated only from the type of power source indicated on the marking label.If you are not sure of the type of power supply at your home, consult your television dealer or local power company. For television sets designed to operate from battery power, refer to the operating instructions.
Page 6
Date:20-Dec-2017 REV.NO: Rev No. 1.0 DATE : PRODUCT SPECIFICATIONS LED TV CATEGORY: 43" Linux Smart FHD LED TV MODEL NO: TH-43FS430M REFERENCE MODEL (PANASONIC/COMPETITION): CHASSIS / Main Board: NT72 ID PHOTO REMOTE: Add Picture PARAMETERS SPECIFICATIONS REMARKS (IF ANY) ME/AF:ENGLISH/FARSI/...
Page 7
NT72563 Factory Menu Spec V1.0 2017.10.17 Drafted by Checked by Approved By...
CONTENTS INTRODUCTION ............................1 OPEN THE FACTORY MENU METHOD ....................1 WHITE BALANCE ............................2 OTHER SUBMENU ............................. 3 NVM RESET SUBMENU ..........................4 PRESET FACTORY CHANNEL SUBMENU ..................4 POWER ON MODE SUBMENU ........................ 4 USB CLONE&&UPDATE SUBMENU ..................... 4...
Date 2017/10/18 Page Index V1.0 of 5 pages Name 1 Introduction ITEM STATE COMMENT REMARK when set On, we can enter factory menu with pressing FAC_HOTKEY On/Off Factory out :OFF return on remote control directly. Only in TV source will display noise picture Aging mode ON:The when WARM-UP set on...
Date 2017/10/18 Page Index V1.0 SCBC R&D of 5 pages Name 2.2 In case of “Factory Key” is enabled, just press RCU “Return” key to pop-up again the Factory menu. 3 White balance Item Sub-item Value Note Source HDMI/TV/AV Standard Color temperature Warm Select Tone by pressing”<...
Date 2017/10/18 Page Index V1.0 of 5 pages Name Print_Enable On/Off Press “< >” key to enable/disable DBC_Enable On/Off Press “< >” key to enable/disable 4 Other submenu Item Sub-item Value Note Watch Dog Watch Dog On/Off Press “< >” key to enable/disable Update CI+ Update CI+ Credential Press “ok/>”...
Date 2017/10/18 Page Index V1.0 of 5 pages Name 5 NVM Reset submenu Item Sub-item Value Note Press “ok/ >” key to default NVM according to selected Project ID(all Reset adjustments are defaulted, channel Maps are cleared, Hotkey is enable,…) 6 Preset Factory Channel submenu Item Sub-item...
Page 13
Date 2017/10/18 Page Index V1.0 of 5 pages Name Press “ok” key to upgrade HDCP2.0 Upgrade HDCP2.0 key Press “ok” key to upgrade HDCP Upgrade HDCP key Press “ok” key to upgrade WideVine Upgrade WideVine Press “ok” key to upgrade Device id Upgrade Device ID...
Page 16
U 27G PANEL_EN_IC G PC _0/ STSI N 0_C LK/ I N T_1/ I 2C _M B_SD A C I _A0 G PB_2/ C I _H A0/ C I _ALE0/ AR M _U AR T_D _R X/ I 2C _M G PC _1/ STSI N 0_VALI D / I N T_2/ I 2C _M B_SC L C I _A1 G PB_3/ C I _H A1/ C I _ALE/ I 2S_I N _BC LK/ N AN D _D 1...
Page 17
3V3_M 3V3_STB BS3_IC BS0_I C BS4_IC 3V3_STB BS8_IC BS9_IC BS12_IC LED_OUT_IC BS15_IC BS19_IC R20 R21 R22 R23 BS20_IC R26 R27 R28 U 27I 3V3_STB 1.8_EMMC VDD33_STBC VDD_EMMC 路 VDD33_NET G N D VD D 25_D LL 2V5_M G 18 G N D G 19 G N D G 20...
Page 25
Trouble shooting diagram Terms: IR: Infrared Receiver RC: Remote Control IR logic: IR blink with RC action LVDS: Low Voltage Differential Signal, output from processor and input for panel O/C: Open Cell, panel with source board BL: Back Light, light source for panel module LB: LED (Light Emitting Diode) Bar, light source for BL module VBL: Voltage for Back Light (before Boost) VLED: Voltage for LED (after Boost)
Page 26
1.No power No power LED, RC or Key can not turn on TV. Power LED no light/no change.
Page 27
2.No Display / Black Panel Back light is OK, sound is OK, but no picture.
Page 28
3.No back light Power LED logic OK, sound OK, but no picture(Different from No Display).
Page 29
4.No sound One or all signal source without sound.
Page 30
5.Signal source no function One or several source no function.