Advertisement
MOUNTING & WIRING (continued)
4.
Select appropriate fixture wire to match incoming voltage.
Models WL400HPS & WL400MH are shipped with 277 V wire
ready for connection. Models WL400HPST & WL400MHT are
shipped with 347 V wire ready for connection. If supply voltage
is lower, cap wire marked 277V (or 347 V for tri-tap models) with
appropriate twist on wire connector and strip fixture wire marked
with matching voltage. (See Figure 3 through Figure 6)
5.
Feed the matching voltage fixture wire, fixture wire marked
"COM", and bare copper fixture grounding wire through the
locknut and then out of the fixture.
6.
Confirm all unused voltage fixture wires are appropriately
capped within fixture body.
7.
Using provided twist on or other approved connectors,
connect the fixture wires to the supply wires.
a.
Connect the selected voltage fixture wire to the Black
(hot) supply wire.
b.
Connect the White fixture wire marked "COM" to the
White (neutral) supply wire.
c.
Connect the Green (fixture ground) wire to the supply
grounding wire.
8.
Mount fixture to wall. Fixture should be mounted horizontal.
(See Figure 2)
9.
Install reflector and secure with (4) screws.
10.
Screw lamp into lampholder until finger-tight.
11.
Install, close, and secure lens cover with (2) screws making
sure that the gasket is properly seated. To weatherproof
fixture, seal all holes in housing (mounting conduit, plugs,
photocontrols, etc.) with silicone sealant.
277 V
240 V
208 V
120 V
CAP
COM
347 V
277 V
120 V
CAP
COM
If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option,
free of charge. This warranty is extended to the original purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident,
dropping or abuse in handling, acts of God or any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modified;
(c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs; (f) the finish on any portion of the
product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY
IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL
BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED
WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of pur-
chase, postage prepaid to the authorized service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove,
Illinois 60081-9698/815-675-7000 http://www.intermatic.com Please be sure to wrap the product securely to avoid shipping damage.
THESE INSTRUCTIONS DO NOT COVER ALL VARIATIONS IN EQUIPMENT, NOR DO THEY PROVIDE FOR ALL SITUATIONS
RELATED TO FIXTURE INSTALLATION, OPERATION OR MAINTENANCE. FOR FURTHER INFORMATION CONTACT YOUR
DISTRIBUTOR OR INTERMATIC INCORPORATED - SPRING GROVE, ILLINOIS 60081 (815) 675-7000 www.intermatic.com
X3
X1
WL400HPS
LAMP
(High Pressure
IGN-01
Sodium)
Figure 3
X2
COM
X3
X1
WL400HPST
LAMP
(High Pressure
IGN-01
Sodium w/tri-tap)
Figure 5
X2
COM
LIMITED 1 YEAR WARRANTY
Alternate wiring: If desired connections may be made inside
fixture using supply wire rating minimum 125°.
12.
To operate, restore power to the circuit and switch light on.
CAUTION
(Metal Halide Lamps Only)
Do not use lamp beyond manufactures rated life to reduce
chance of lamp rupture.Turn lamp off at least once for 15
minutes per week to reduce chance of lamp rupture.
LAMP REPLACEMENT
CAUTION
Use lamp of correct type and wattage as specified on fixture.
1.
Turn off power at circuit breaker or fuse box. Allow fixture and
lamp to cool.
2.
Loosen (2) screws open and remove fixture lens cover.
Remove old lamp and replace with new lamp of correct type
and wattage. Screw lamp into socket in lampholder until
finger-tight.
3.
Install, close, and secure lens cover with (2) screws making
sure that gasket is properly seated, free of debris, and
compressed to seal out moisture.
4.
Turn power back on.
5.
Properly dispose of lamp per manufacturer's
recommendations.
277 V
240 V
208 V
120 V
COM
347 V
277 V
120 V
COM
CAP
WL400MH
LAMP
(Metal Halide)
Figure 4
COM
CAP
WL400MHT
LAMP
(Metal Halide
w/tri-tap)
Figure 6
COM
158--00107
Advertisement
