Installation - ubbink MiniBright 3LED Manual

1 MiniBright 3 LED
The MiniBright 3-LED is an underwater lamp. Use with low voltage, includes transformer for outdoor use (IP 44). The socket for the transformer must be at
least 3.5 m from the pond.
Type
Nominal voltage
Lamp
Transformer
Cable length
Nominal power
Max. installation depth
Guarantee
Includes
Safety instructions
• The pond fl oodlight must be connected to a network with 230 VAC/50 Hz via a safety transformer according to the requirements of the harmonised EU-Directives,
EU-Safety standards and product-specifi c standards. Possibly ask your local utility regarding connection regulations.
• The safety transformer used must be connected to an outside safety socket with earth (IP X4) at a distance of at least 3.5 m from the pond.
• The connected bulb capacity must not exceed the rated capacity of the safety transformer! A too high load may damage the transformer beyond repair. Only a
safety transformer recommended for this should be used for correct operation of the pond fl oodlight.
• The pond fl oodlight is intended for underwater use. Pay attention that the fl oodlight is always fully submerged in the water to guarantee suffi cient cooling of the
fl oodlight.
• Do not use the cable for carrying the pond fl oodlight and never pull at the cable.
• The electric cable cannot be replaced. If the cable is damaged, the pond fl oodlight must not be used any longer and must be correctly disposed.
• The power supply must always be disconnected during assembly and disassembly of the pond fl oodlight and during maintenance work.
• The device is not suitable for usage by persons (Including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge,
unless supervised by a person responsible for their safety or they have been instructed in the usage of the device. Children must be supervised to ensure that
they are not playing with the device.

Installation

The MiniBright 3-LED is just perfect for fl oodlighting water ornaments. This is done as follows (see the illustrations):
1. Slide the spotlight through the T-section and hose.
2. Push the rubber cap on to the light cord below the T-section and then onto the T-section.
3. Slide the hose and spotlight upwards though a cover or grate.
4. Finally, place the ornament on the cover/grate, on top of the hose and light.
Changing the LED
1. Remove the mains plug from the socket.
2. Remove any residual water.
3. Pull out the glass tube of the bulb.
4. Replace the bulb (do not touch the bulb with your fi ngers).
5. Slide the cover of the lamp (thoroughly dried) back on.
Cleaning
Follow the same instructions as for changing the LED. Use only water and a soft brush. Ensure that no damp enters the fi tting!
Repair
It is not possible to repair damage to the cable, housing or transformer. The product may then no longer be used, and should be destroyed.
2
Guarantee
We give a 2-year guarantee from the date of purchase on materials and manufacturing defects for this product. To make a claim under this guarantee, the original
invoice must be submitted as proof of purchase. Claims brought about by incorrect installation or operation, inadequate maintenance, the eff ects of frost, inexpert
attempts at repair, the use of force, wrongful acts by a third-party, overloading and foreign objects, as well as all damage to parts resulting from wear and tear, are
not covered by this guarantee.
By virtue of the Product Liability Act, we are not liable for damage caused by our equipment, if this is the result of inexpert repairs.
Environmental Protection
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
Manual minibright 3 led.indd 3
MiniBright 3LED
230VAC/50Hz
LED G4 12VAC - 24SMD
230VAC/12VAC 6 VA
5 m
3 x 0,5W
0.2 m
2 years
transformer for outdoor use (IP44)
21-10-15 17:31