Subscribe to Our Youtube Channel
Related Manuals for DR.ÖTEK MT-X
Summary of Contents for DR.ÖTEK MT-X
- Page 1 DR.ÖTEK User Manual Metal Detector MT-X If there are any issues and are not 100% satisfied for any reason, please contact us at support@drotekor.com...
- Page 2 Read this manual carefully before using. Most importantly, review the TIPS, QUICK START and BASIC OPERATION. TIPS 1. The metal detector is used outdoors, not fit for using indoors. 2. Sensitivity Indication cursor shared with the coin depth Indication Cursor, DEPTH 2”, 4” and 6”, equivalent to SENS 1, 2 and 3, when detecting metals, it turns into depth cursor automatically.
-
Page 3: Package Contents
Search Coil: 210*70mm open waterproof search coil ● Earphone Jack: 1/8 inch earphone jack (earphone not supplied) ● Power Supply: 6 AA batteries (batteries not supplied) ● ASSEMBLY The structure of MT-X is shown in the figure below. - 1 -... - Page 4 1. Loosen the two triangular fasten buttons below the control box, insert the bracket, then tighten the two triangular fasten buttons. (See Fig.1) 2. Press the silver-white shrapnel on the plastic connecting rod, insert to the black aluminum stem. When the silver-white shrapnel popping up from the hole on the black aluminum stem, you could use the unit.
- Page 5 3. Wind the cable around the aluminum tube, keep the elastic moderate, so that the cable won’t sway. 4. Relax two side nuts of the search coil, adjust the position of search coil, let the search coil be parallel to the ground. Be careful not to mistake the location of the search coil.
- Page 6 2. Insert the 6 AA batteries to the case as indicated by the polarity symbols marked inside the case. (See Fig.5) 3. And then push the battery cover in the battery cavity. A KATA tone will be heard, which means the battery cover has been in the right position.
- Page 7 Target ID Pattern: It’s located on the LCD screen. It indicates the ● wanted target metals. When detecting a metal target, the target ID cursor will appear below such metal patterns or the words. Target ID Cursor: It’s in the shape of .
- Page 8 Coin Depth Indication Cursor: It contains three grades, namely 2”, ● 4”and 6”, equivalent to 1, 2 and 3. It indicates the approximate depth of the 2P copper coin in the neutral soil. It’s only the approximate depth. The size and composition of the target, and the composition of the soil will affect the indication value.
-
Page 9: Quick Start
Power Button: Press the button once, the power is on, and press it ● once more, the power is off. SENS Button: Choose the 3 levels with the SENS button. Default ● setting is the middle level (the second level). The highest sensitivity is the third level, when there is interference, you can set the sensitivity lower properly. - Page 10 3. Turn on Press the POWER button, and the detector will sound two moo tones, all the LCD patterns are lighted at minute, the detector is in the ALL METAL mode by default, and the sensitivity is in the second grade. (See Fig.9) Fig.9 4.
- Page 11 (See Fig.10, take iron nail as an example) 5. PINPOINT mode test a) Press and hold down the “PINPOINT” button, the PINPOINT cursor is lighted, and the depth cursor points to the third grade. The detector will sound a low single-frequency mediant. (See Fig.11) b) Let the 2P copper coin approach the search coil slowly, when it is in the position of about 6”...
-
Page 12: Basic Operation
c) Maintain the position of the 2P copper coin then release the PINPOINT button. Press the PINPOINT button again after several seconds, the lower cursor is extinguished, and the sound comes back to the initial state, the depth indication comes back to the full scale. d) Let the 2P copper coin move to the center of the search coil again slowly, the lower cursor appears again and increases, the sound turns louder again, the depth cursor goes lower again, which means the... - Page 13 the LCD patterns are lighted at minutes. Then the sensitivity will be to the preset second grade, and the operation mode will be to the preset ALL METAL mode. 2. Set the operation mode In general, the user can choose the preset ALL METAL mode. At this time, the detector will respond to all kinds of metals.
- Page 14 decrease the sensitivity appropriately. 4. Move the search coil When detecting, you should move the search coil at a constant speed, not unsteadily. Let the search coil be parallel with and about 1/2 inch from the surface, not to swing it like a pendulum high and low above the ground.
- Page 15 6. PINPOINT When detecting in the motion mode, as you should persistently move the search coil, so although you find the region that burying metals, it’s not easy for you to determine the exact location, it gets the digging difficult. At this time, you should recur to the PINPOINT mode. a) Press and hold down the PINPOINT button, the detector will sound a low single-frequency tone, and the sensitivity is in the highest state.
- Page 16 7. Depth and Target Indication (only in the motion mode) Preset the detector in the motion mode. The LCD screen will show the rough metal target types and the rough target depth. When the position and type of the target are determined, the detector will send a repeated signal.
- Page 17 8. The use of the non-motion mode. In fact, the sensitivity in the non-motion mode is high, search metals directly using non-motion mode is also a choice. In some regions, the ground is too narrow to sweep search coil, you could choose the PINPOINT mode.
-
Page 18: Troubleshooting Guide
TROUBLE SHOOTING GUIDE SYMPTOM SOLUTION 1. Be sure that the batteries are installed correctly. No power, no boot 2. Be sure that the “UP” of the battery cover is sound, and the LCD upward. have no indication. 3. Replace the batteries. Sound a successive 1. -
Page 19: Warranty
ID and details of the issue. We will reply to you within 24 hours. 2. We recommend registering your MT-X the day you receive it, so that we can help you as quickly and efficiently as possible. - Page 20 Model: MT-X Thank you for choosing DR.ÖTEK! Support Email: support@drotekor.com We answer most emails in less than 24 hours.
Need help?
Do you have a question about the MT-X and is the answer not in the manual?
Questions and answers