Subscribe to Our Youtube Channel
Related Manuals for HYCON HY16F3910 Series
Summary of Contents for HYCON HY16F3910 Series
- Page 1 HY16F3910 Series IDE Hardware User’s Manual © 2022 HYCON Technology Corp. APD-HY16F39IDE003-V02_EN www.hycontek.com...
-
Page 2: Table Of Contents
Target Board Circuit Diagram ......................12 4.5. LCD Board Introduction ........................13 4.6. HY16F Mini Link Debug Tool and Target Board Hardware Connection Steps ........16 HARDWARE CONNECTION INTRODUCTION ..................17 REVISIONS ............................. 18 © 2022 HYCON Technology Corp APD-HY16F39IDE003-V02_EN www.hycontek.com page2... - Page 3 HY16F3910 IDE Hardware User’s Manual Attention: 1、 HYCON Technology Corp. reserves the right to change the content of this datasheet without further notice. For most up-to-date information, please constantly visit our website: http://www.hycontek.com 2、 HYCON Technology Corp. is not responsible for problems caused by figures or application circuits narrated herein whose related industrial properties belong to third parties.
-
Page 4: Package Contents
HY16F Mini Link Debug Tool(refer to table 1-1). Integrated Hardware development kit helps to develop MCU application program of HY16F3910 Series. Program compiling, hardware debug, IC programming was implemented through NB/PC end connection. This user’s manual mainly introduces the IDE hardware development tool, the related hardware is equipped as shown below: Model No. -
Page 5: Safety Precautions
When following status occurred, please remove the power supply immediately, and contact our engineer. Power Supply line is worn or damaged. Power source (battery) connected but no any light on while operating. Component off. © 2022 HYCON Technology Corp APD-HY16F39IDE003-V02_EN www.hycontek.com page5... -
Page 6: Software Installation Requirements
Supported Hardware Model No.: HY16F3910-DK01: HY16F3910 hardware development kit. Supported software version: AndeSightV3.2.1RDS above HYCON 32-bit MCU Device V0.34 above Supported Operating system: Windows XP (32-Bit System), Windows 7(32/64-Bit System), Windows 8(32/64-Bit System), Windows 10(32/64-Bit System). Apply the following interface modes:... -
Page 7: Description Of The Hardware Tool
(1) Power LED Function: Power LED (Green LED) Description: When the USB Port is connected to a computer or an external 5V power supply, the light indicates that the Control Box is powered. © 2022 HYCON Technology Corp APD-HY16F39IDE003-V02_EN www.hycontek.com page7... - Page 8 EDM Clock Pin, connected to the ECK pin of the HY16F3910. EDM Data Input / Output Pin, connected to the EDIO pin of the EDIO HY16F3910. Ground Pin, connected to the VSS pin of the HY16F3910. © 2022 HYCON Technology Corp APD-HY16F39IDE003-V02_EN www.hycontek.com page8...
-
Page 9: Introduction To Target Board
IDE Hardware User’s Manual 4.3. Introduction to Target Board The Target Board (model: HY16F3910-IM01) is commonly used for HY16F3910 series products (Figure 4-3) and demonstrate the function of HY16F3910. The following describes the appearance and functions of the Target board:... - Page 10 It can be used to measure chip current by ammeter. Description: Pin are defined as follows Name Name VDD5V Note: When J3 pin is not used to measurement, keep the J3 pin shorted together. © 2022 HYCON Technology Corp APD-HY16F39IDE003-V02_EN www.hycontek.com page10...
- Page 11 Function: Target Board Chip’s ADC Bridge Sensor Connector and it can measure circuit. The ADC Bridge Sensor is composed of AIO0, AIO1, AIO2 and AIO3. Description: Pin are defined as follows Name © 2022 HYCON Technology Corp APD-HY16F39IDE003-V02_EN www.hycontek.com page11...
-
Page 12: Target Board Circuit Diagram
SEG33 PT97 PT66 SEG8 PT9.7/SEG33 PT6.6/SEG8 SEG32 PT96 PT67 SEG9 PT9.6/SEG32 PT6.7/SEG9 Note: This Target Board circuit diagram is is placed in the Andes IDE software directory installed below: " \Andestech\AndeSight_RDS_v321\doc\Hycon\ICESchematic\ “. © 2022 HYCON Technology Corp APD-HY16F39IDE003-V02_EN www.hycontek.com page12... -
Page 13: Lcd Board Introduction
HY16F3910 IDE Hardware User’s Manual 4.5. LCD Board Introduction The LCD panel (model:HY10000-AM01) on HY16F3910-N088 Target Board is HYCON self-owned mold, it’s symbol and pin diagram is shown in below graph. It’s panel specification is as follows: (1) Operating Voltage: 3.0V... - Page 14 SEG0 SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 COM0 COM1 COM2 COM3 ...
- Page 15 ...
-
Page 16: Hy16F Mini Link Debug Tool And Target Board Hardware Connection Steps
Use the USB Cable to connect to the HY16F Mini Link Debug Tool USB Port and the computer's USB port (Power LE Step4: After Step 1~3 (as shown in Figure 4-5), the hardware connection is completed. Power LED Step3 Step2 Step1 Figure 4-5 © 2022 HYCON Technology Corp APD-HY16F39IDE003-V02_EN www.hycontek.com page16... -
Page 17: Hardware Connection Introduction
(2.1) In the Target Manager: Local Targets window (2.2) Select HY16F3910 by right-clicking(Select Connect Target via AICE) (2.3) Successful connection appears HY16F3910 ICE-ICE:9904 (2.4-2.5) From the Console window, can see the version information of the Mini Link:Andes AICE-MINI v1.0.1 © 2022 HYCON Technology Corp APD-HY16F39IDE003-V02_EN www.hycontek.com page17... -
Page 18: Revisions
HY16F3910 IDE Hardware User’s Manual 6. Revisions The following describes the major changes made to the document, excluding the font and punctuation changes. Version Page Date Revision Summary 2022/05/17 First edition © 2022 HYCON Technology Corp APD-HY16F39IDE003-V02_EN www.hycontek.com page18...
Need help?
Do you have a question about the HY16F3910 Series and is the answer not in the manual?
Questions and answers