Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Pelsue 1590
Summary of Contents for Pelsue 1590
- Page 1 Part #107077-001 Product Manual: Model #1590 Construction Heater / Blower I S O 9 0 0 1 C er tif ied T.A. Pelsue Company 2500 South Tejon Street Englewood, Colorado, USA 80110 Tel. 800-525-8460 or 303-936-7432 Fax. 303-934-5581 Internet: www.pelsue.com...
- Page 2 Page 2 107077-001 - Product Manual - Model #1590 Axial Construction Heater / Blower - Rev. 05 - 07-01-2015...
- Page 3 Pelsue continues the dedication that industry throughout the world. has made it pre-eminent in this field. Page 3 107077-001 - Product Manual - Model #1590 Axial Construction Heater / Blower - Rev. 05 - 07-01-2015...
-
Page 4: Table Of Contents
5.0........Product Operation........15 5.1 ......Product Description & Capabilities 5.2 ......Start-Up & Operating Procedures 6.0........Troubleshooting........18 7.0........Storage............18 8.0........Contact Information........19 Page 4 107077-001 - Product Manual - Model #1590 Axial Construction Heater / Blower - Rev. 05 - 07-01-2015... -
Page 5: General Information
EVERY T.A. PELSUE COMPANY EMPLOYEE IS ExPECTED TO COMMIT TO THIS PHILOSOPHY IN THE PERFORMANCE OF HIS OR HER DAILY TASkS. QUALITY FIRST! T.A. PELSUE COMPANY SENIOR MANAGEMENT TEAM Page 5 107077-001 - Product Manual - Model #1590 Axial Construction Heater / Blower - Rev. 05 - 07-01-2015... -
Page 6: Pelsue Product Warranty
In the event of failure of any components of a Pelsue product within the warranty period, service must be pre- ... -
Page 7: Introduction & Product Information
2.0 - Introduction & Product Information Congratulations on your choice of a Pelsue Model #1590 Construction Heater / Blower. The Pelsue Heater / Blower is specifically designed to provide means of heating ventilated shelters or work areas. Such use includes, but is not limited to Fire, Police &... -
Page 8: Configuration & Assembly
3.0 - Configuration & Assembly Upon initial receipt of the Model #1590 Construction Heater / Blower, inspect the packaging for any evidence that the product may have been damaged in shipment. While unpacking the product, inspect all of the components for damage. - Page 9 FITTING - ELL, STREET, 90°, LOW PROFILE, 1/4" NPT, BRASS 107609-001 FITTING - 1/4" NPT x 1/4" TUBE, 90° FEMALE Table 3.1a: #1590 Parts List (continued) Page 9 107077-001 - Product Manual - Model #1590 Axial Construction Heater / Blower - Rev. 05 - 07-01-2015...
- Page 10 3.1 Parts Diagram & List (continued) Figure 3.1b: #1590 Parts Diagram Figure 3.1c: #1590 Parts Diagram Page 10 107077-001 - Product Manual - Model #1590 Axial Construction Heater / Blower - Rev. 05 - 07-01-2015...
- Page 11 RIVET - STAVEx, BLIND FLANGE DOME, BLACk, .188" DIA 62E-011200 GROMMET - RUBBER, 3/8" ID x 3/4" OD Table 3.1a: #1590 Parts List (continued) Page 11 107077-001 - Product Manual - Model #1590 Axial Construction Heater / Blower - Rev. 05 - 07-01-2015...
-
Page 12: Wiring Diagram
(BK) (BK) (WT) (WT) (GN) (GN) BUTT SPLICE 14/16 (3X) PLUG 120 VAC, 60 HZ Figure 3.2a: #1590 Motor Wiring Diagram Page 12 107077-001 - Product Manual - Model #1590 Axial Construction Heater / Blower - Rev. 05 - 07-01-2015... -
Page 13: Safety
4.0 - Safety The following section will address the safety precautions which must be adhered to when working with the Pelsue Construc- tion Heater. Any user must familiarize themselves with the information in this section before utilizing the equipment. SIGNAL WORDS: Note the use of the signal words DANGer, WArNING and CAuTION with the safety messages. -
Page 14: General Safety Information
1,000 BTUH of the heater’s rated output should be provided. The #1590 is rated at 45,000 BTU’s, thus the flow must maintain a volumetric rate of at least 180 CFM (the #1590 is rated at 432 CFM in a free air configuration). -
Page 15: Product Operation
5.0 - Product Operation The following section will address the capabilities and the general operation of the Pelsue Model #1590 Axial Construction Heater / Blower. The instructions contained within this section should be adhered to each and every time the product is used. - Page 16 After this delay the pilot should be lit, and the heater should fire. f. Connect a Pelsue heat-resistant blower hose to the heater outlet, in order to direct fresh, heated air to desired location.
- Page 17 1590 Heater 1.5m Ventilation Hose Air Flow Alarm (optional) Confined Space Figure #5.2c: 1590 Heater / Blower Setup for Confined Spaces Page 17 107077-001 - Product Manual - Model #1590 Axial Construction Heater / Blower - Rev. 05 - 07-01-2015...
-
Page 18: Troubleshooting
4. If a malfunction in the pressure regulator or safety shut-off control valve is found after placing the heater into opera- tion, consult the factory or an experienced heating contractor for repair or replacement. Page 18 107077-001 - Product Manual - Model #1590 Axial Construction Heater / Blower - Rev. 05 - 07-01-2015... -
Page 19: Contact Information
T.A. Pelsue Company 2500 S. Tejon St. englewood, CO 80110 Toll Free: 1-800-525-8460 Telephone: 1-303-936-7432 Fax: 1-303-934-5581 Website: www.pelsue.com email: sales@pelsue.com Page 19 107077-001 - Product Manual - Model #1590 Axial Construction Heater / Blower - Rev. 05 - 07-01-2015... - Page 20 T.A. Pelsue Company 2500 South Tejon Street, Englewood, Colorado, USA 80110 Toll free 800-525-8460 or 303-936-7432 Fax. 303-934-5581 ISO 90 0 1 Certified Internet: www.pelsue.com Email: sales@pelsue.com...
Need help?
Do you have a question about the 1590 and is the answer not in the manual?
Questions and answers