Advertisement
Quick Links
Advertisement
Related Manuals for Mitsubishi Electric MAC-558IF-E
Summary of Contents for Mitsubishi Electric MAC-558IF-E
- Page 1 INSTALLATION GUIDE...
- Page 2 Telephone number Wi-Fi Control minimum requirements for operation. • Compatible WPS capable wireless network with coverage including the heat pump installation location • A PC/Tablet/Smartphone that is iOS/Android/Windows compatible • A compatible Mitsubishi Electric Heat Pump with a MAC-558IF-E Adaptor...
- Page 3 Mitsubishi Electric Wi-Fi Heat Pump Control Register Your Heat Pump(s) Thank you for choosing a Mitsubishi Electric Designer Series Heat Pump with Wi-Fi Control. Once your adaptor is installed either download the app (search term: Mitsubishi Control) or visit our website to register your heat pump(s).
- Page 4 Wi-Fi Control: Installation Instructions Information for installers The following steps explain how to connect the MAC-558IF-E Adaptor to a Mitsubishi Electric Designer Series Heat Pump. EQUIPMENT REQUIRED FOR INSTALL: MAC-558IF-E WPS Enabled Wi-Fi Tools to remove Adaptor Router Installation cover of indoor...
- Page 5 Remove the cover of the indoor Locate the CN105 port on the unit, the cable terminal, and the main control board and connect cover to the control unit board. MAC-558IF. Reassemble the air conditioning Run the cables down the back of unit and restore power to the the unit with the other cables.
- Page 6 Wi-Fi Control: Installation Instructions Information for users The following steps explain how to connect the MAC-558IF-E Adaptor to a router. KEY (LED LIGHTS): FLASHING Check Wi-Fi and WPS are enabled Activate WPS on your router. on your router. Connection This will be enabled for a set...
- Page 7 Next, the bottom light (LED 3) will When LED 1 remains solid for 5 start flashing as it connects to the seconds the adaptor is connecting internet. This may continue for up to your router. to 10 minutes. When LED 1 and LED 3 flash If LED 2 (orange) lights up at any alternately the unit is successfully stage there may be a problem.
-
Page 8: Table Of Contents
• Improper connection and mounting may result in • Do not connect the Wi-Fi adaptor to earth inside breakdown, heat generation, smoke generation, the air conditioner. or fire. • Mitsubishi Electric components or other designated components must be used for installation. -
Page 9: Product Introduction
Third party Wi-Fi adaptor cannot connect to Mitsubishi Electric’s Wi-Fi service. Mitsubishi Electric is not responsible for any (i) under performance of a system or any product; (ii) system or product fault; or (iii) loss or damage to any system or product; which is caused by or arises from connection to and/or use of any third party Wi-Fi adaptor or any third party Wi-Fi service with Mitsubishi Electric equipment. -
Page 10: Parts
3. Parts Adaptor unit Mounting cord [with connecting cable clamp (5-core)] Fastener Screw for mounting (for bundling the 3.5×16 wires) Screw for mounting 4×16 4. Connecting the Wi-Fi Adaptor (For details on each system, see the relevant instruction manual.) • Before dismantling the indoor unit turn off and verify the power has been disconnected to the complete air-conditioning system. -
Page 11: Led Pattern
6. LED pattern :OFF :Flashing Description LED1 LED2 LED3 Power is ON or software downloaded (0.5-sec interval) (0.5-sec interval) (0.5-sec interval) ALL settings reset WPS activated (PBC) (0.5-sec interval) WPS activated (PIN) (0.2-sec interval) WPS enabled (5-sec) WPS failed (5 sec) Server and access point communication connected, and air conditioner communication failed (once every 5 sec) - Page 12 Contact Details Mitsubishi Electric New Zealand Mitsubishi Electric Australia www.mitsubishielectric.com.au/wifi www.mitsubishi-electric.co.nz/wifi WELLINGTON SYDNEY // HEAD OFFICE // HEAD OFFICE 1 Parliament Street 348 Victoria Road PO Box 30772 Rydalmere Lower Hutt 5040 NSW 2116 Phone 0800 639 434 Phone (02) 9684 7777...