Table of Contents
Advertisement
Quick Links
MOLEAER KINGFISHER
NANOBUBBLE GENERATOR
Owner's Manual
IMPORTANT: READ, FOLLOW AND
SAVE THESE INSTRUCTIONS
CUSTOMER SERVICE / TECHNICAL SUPPORT
If you have questions or need to order
replacement parts, please contact:
CUSTOMER SERVICE:
Monday to Friday: 8:00 a.m. to 5:00 p.m. PST
Phone: +1 (424) 558-3567
Email: info@moleaer.com
WEBSITE:
www.moleaer.com
Advertisement
Table of Contents
Related Manuals for MOLEAER KINGFISHER
Summary of Contents for MOLEAER KINGFISHER
- Page 1 If you have questions or need to order replacement parts, please contact: CUSTOMER SERVICE: Monday to Friday: 8:00 a.m. to 5:00 p.m. PST Phone: +1 (424) 558-3567 Email: info@moleaer.com WEBSITE: MOLEAER KINGFISHER www.moleaer.com NANOBUBBLE GENERATOR Owner’s Manual IMPORTANT: READ, FOLLOW AND SAVE THESE INSTRUCTIONS...
-
Page 2: Table Of Contents
MOLEAER KINGFISHER NANOBUBBLE GENERATOR Owner’s Manual Table of Contents Safety ...................................... 2 General Warnings ................................2 General Information ................................3 Key System Components ..............................3 Quick Startup Guide ................................4 Suction and Discharge Verification ............................. 4 Typical Operating Parameter Ranges ..........................4 Specifications .................................. -
Page 3: Safety
Never open the inside of the pump motor enclosure. There is a capacitor bank that holds an electrical charge even The Kingfisher unit is designed to deliver a micro-dose of when there is no power to the unit. Ozone nanobubbles to the waterbody. Depending on the... -
Page 4: General Information
2. On/Off indicator light Read instructions thoroughly prior to installation and use. 3. Cooling air discharge All Kingfisher products are factory adjusted for optimal nanobubble production. Note that the actual unit sold 4. Water pump inlet may differ slightly from the description in the manual without 5. -
Page 5: Quick Startup Guide
Table 1. 1. Review detailed location and piping installations prior to installing the Kingfisher unit. Table 1. Kingfisher Typical Operating Parameter Ranges 2. Open the lid of the Kingfisher and hand-tighten any Parameter Kingfisher loose fittings. 3. Plug the unit power cord into the GFCI outlet. -
Page 6: Power Input Requirements
MOLEAER KINGFISHER NANOBUBBLE GENERATOR Owner’s Manual Power Input Requirements Pump Specifications Table 2. Kingfisher Power Input Requirements Table 5. Kingfisher Pump Specifications 60 Hz (North America) Single Phase, 115 VAC Anbull SP-1100A or Equipped Pump Brand: equivalent 50 Hz Single Phase, 230 VAC Power 1.5 HP / 1.1 kW... -
Page 7: Installation & Startup
Carefully select the installation location based on Table 6. Kingfisher Accessories the requirements specified in this section. Locate the Kingfisher as close to the waterbody as possible in an open Image Line KINGFISHER area of level ground. Use the guidelines shown in Figures Item 4 and 5 to locate the suction screen. -
Page 8: Drawings
MOLEAER KINGFISHER NANOBUBBLE GENERATOR Owner’s Manual Drawings Figure 4: Kingfisher Installation Diagram Figure 5: Kingfisher Installation Diagram from Top www.moleaer.com CONFIDENTIAL... -
Page 9: Pipe Assembly
• recommendations detailed in Figures 4 and 5. • PVC saw The intake and discharge ports on the Kingfisher are both 1.5” (63 mm) union fittings. PVC pipe primer and PVC pipe cement • Locate and install the intake structure and suction pipe PVC Pipe or hose and fittings to connect to the •... -
Page 10: Ozone Bypass
Once primed, large bubbles or a large air pocket should not ready to start up the normal operation of the Kingfisher. be visible in the strainer basket. If large bubbles or an air... -
Page 11: Pump Maintenance
MOLEAER KINGFISHER NANOBUBBLE GENERATOR Owner’s Manual Pump Maintenance 7. Fill the pump basket up to the inlet port with water. 8. Clean the lid and clamp, O-ring, and sealing Do NOT open the strainer basket if pump fails to surface of the pump basket. - Page 12 2. If a motor has been damaged by water the motor warranty is voided. PUMP SERVICE Always disconnect power to the Kingfisher generator and / or pump at the circuit breaker before servicing the pump. Failure to do so could result in death or serious injury to service people, users or others due to electric shock.
-
Page 13: General Arrangement Drawing (Gad)
MOLEAER KINGFISHER NANOBUBBLE GENERATOR Owner’s Manual General Arrangement Drawing (GAD) Figure 9: Kingfisher Dimension Drawing www.moleaer.com CONFIDENTIAL... -
Page 14: Solvent Welding Pvc Pipe
MOLEAER KINGFISHER NANOBUBBLE GENERATOR Owner’s Manual Solvent Welding PVC Pipe Figure 11. How to Glue Piping Once the primer has been applied to both surfaces, • the cement must be applied within 5 minutes. If not, you MUST prime the surfaces again before applying cement. -
Page 15: Cleaning And Sanitizing
• Visible bubble from the discharge pipe are 1. Turn off the unit and isolate the Kingfisher from the significantly reduced. waterbody and drain any water in the system. The pressure of the gas injection required to •... - Page 16 MOLEAER KINGFISHER NANOBUBBLE GENERATOR Owner’s Manual Figure 10. CIP Tubing www.moleaer.com CONFIDENTIAL...
-
Page 17: Operation Checklist
MOLEAER KINGFISHER NANOBUBBLE GENERATOR Owner’s Manual Operation Checklist Line Component Instructions Power light Check the light. Green: Running; Red: Powered but not running, No light: No power Gas Leakage Use soap water to check the gas leakage on the joints and fittings. Check for signs of... -
Page 18: Preventive Maintenance Checklist
MOLEAER KINGFISHER NANOBUBBLE GENERATOR Owner’s Manual Preventive Maintenance Checklist Item Description Frequency Pump Check the motor for overheating and pump for proper operations Monthly Tubing Check tubing for leaks and for any damage due to heat/sun. Monthly Strainer Check for debris collected at the strainer and remove/clean as Monthly required. -
Page 19: Troubleshooting Guide
MOLEAER KINGFISHER NANOBUBBLE GENERATOR Owner’s Manual Troubleshooting Guide Problem Possible Cause Corrective Action Pump Will Not • Air being drawn into pump • Check suction piping and valves on suction Prime suction. line. Air pocket in suction line. Secure lid on pump strainer basket and be sure •... - Page 20 MOLEAER KINGFISHER NANOBUBBLE GENERATOR Owner’s Manual Completely flood intake piping by pouring water Excessive Noise • Pump is not fully primed. • in the inlet pipes to prime fully. and Vibration NPSH too high • www.moleaer.com CONFIDENTIAL...
-
Page 21: Limited Warranty
Limited Warranty Moleaer warrants that the Goods will be free from defects in material and workmanship for a period of twelve (12) months from the date of first purchase (provided, however, that if Buyer is not able to provide proof of the date of purchase, the warranty period will run for eighteen (18) months from the date of manufacture) (the “Warranty Period”). - Page 22 MOLEAER KINGFISHER NANOBUBBLE GENERATOR Owner’s Manual 20800 BELSHAW AVENUE CARSON, CA 90746 USA +1-424-558-3567 info@moleaer.com www.moleaer.com Revision 07052022 www.moleaer.com CONFIDENTIAL...
Need help?
Do you have a question about the KINGFISHER and is the answer not in the manual?
Questions and answers