T-Mark T2-2 User Manual

Vehicle gps tracker
Hide thumbs Also See for T2-2:

Advertisement

Quick Links

Vehicle GPS Tracker
User Manual
Model:T2-2
Please read the manual carefully before use
the GPS Tracker so that you can install the device
correctly and activate it quickly on the internet. The
outlook and true color are subject to the actual
product.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T2-2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for T-Mark T2-2

  • Page 1 Vehicle GPS Tracker User Manual Model:T2-2 Please read the manual carefully before use the GPS Tracker so that you can install the device correctly and activate it quickly on the internet. The outlook and true color are subject to the actual...
  • Page 2: Technical Parameter

    1. Technical parameter 1. GSM:850/900/1800/1900MHz 2. GPRS:Class12,TCP/IP 3. Working Voltage:3.90V DC 4. Working current:≈35mA (12vDC) 5. Working current:≈4mA (24vDC) 6. GPS locating time:Cold start≈38s (Open sky) Hot start≈2s (Open sky) 7. GPS Precision:10m(2D RM) 8. Working temperature:-20℃~+70℃ 9. Working humidity:20%~80%RH 10.
  • Page 3: Functional Characteristics

    4.1.3 GSM installation, open the terminal SIM interface that end of the small cap, hand holding a SIM card, the chip side down, there is a gap at the end of the inside, to promote the card slot inside you can. Need to be removed when the top pressing with a finger SIM Carol card slot on the outside, you can pop.(as follow)...
  • Page 4 6.7 Built in 3D accelerator, distinguished between motion and stationary state, intelligent power saving. 6.8 Can be at any time to check the latitude and longitude of the text message. 6.9 6800MA large battery power supply, the use of more long-term. 6.10 Using AGPS program, positioning time is more efficient.
  • Page 5 SET SERVER OK! Feedback (4) GMT Command Parameter Sample GMT,direction,time zone[, 1) GMT,E,8# Parameter half time zone] 2) GMT,E,6,30# The default time zone on the terminal is the Beijing Description time zone E8, if need to change the time zone,need to send the above instructions.Range: E/W,0~12 Feedback SET GMT OK!...
  • Page 6 1 device factory default mode 1, intelligent sleep mode. 2 Intelligent sleep mode, the device will turn off the GPS when it is stationary for 3 minutes, and the exercise can wake up the GPS 3. Deep sleep mode, device in completely dormant state, is not affected by the movement and stillness, Description only to send instructions WAKE# or center number...
  • Page 7 timing mode 3) when the device is not in a dormant state, the instruction is not valid. Feedback WEAK OK! (10) FCALM Command parameter Sample FCALM FCALM,way# FCALM,1# Telephone alarm 1) this instruction in order to set up the alarm after the alarm mode.
  • Page 8 5265 (14) RESET Command Parameter Sample Format RESET# RESET# Description This instruction is used to restart the device Feedback RESET OK! (15) FACTORY Command Parameter Sample Parameter FACTORY# FACTORY# This instruction is to restore the factory settings Descriptio Restore factory settings after all users to add and modify the content will be restored! Feedback SET FACTORY OK!...
  • Page 9 The command is designed for checking the device’s Description working status. BATTERY:100% -- Battery status (SOC) GSM Signal: strength --GSM Signal strength GPS:FIXED --GPS Location condition GPS Signal: strength --GPS Signal strength Feedback Listen:OFF -- Listen status Vibration:0 --Vibration alert status Work mode:1 --Work mode staus Voltage : 4.18...
  • Page 10: Troubleshooting

    When the monitor function is turned on, the central number of the call will not wake up the device, but directly into the listening state, then if you need to wake up the device, can only send text messages WAKE# 12.
  • Page 11: Address Type

    installed correctly or the GSM signals may not reach your location (such as the basement), please drive to the open sky. 1w.4 The red LED is not glow when power on. Check the fuse of the power line. If the fuse is fused, please change the fuse with the seller, and check the device about the inner malfunction, then power on to use again.
  • Page 12 Maintenance Card Maintenance DATE unit Fault statement Maintenance condition IMEI serviceman...

Table of Contents