Related Manuals for ALSENSE ALS Tire BLE
Summary of Contents for ALSENSE ALS Tire BLE
-
Page 1: Als Tire Ble
ALS Tire BLE Install Guide (18.06.2022) V1.0 – Initial version www.alsense.eu [Type here]... -
Page 2: Table Of Contents
ALS Tire BLE Install Guide Table of Contents ALS Tire BLE www.alsense.eu Introduction Specifications Quick Install Initial Setup Configuration Power-up Sleep Mode Physical Installation Mobile Installation Operation & Charging Factory Reset Configuration Troubleshooting / FAQ Support Appendix A: ALS Tire BLE Bluetooth Communication Protocol V2.0 Updated 23.01.2022... -
Page 3: Introduction
ALS Tire BLE Install Guide 1. Introduction Thank you for purchasing the ALS Tire BLE. The following guide is aimed at providing an overview of the typical install process and configuration steps. 2. Specifications SENSOR Number of Channels 3 (3 default) -
Page 4: Quick Install
ALS Tire BLE Install Guide 3. Quick Install a. Initial Setup First step after receiving the product is putting the sensors on charge using the supplied cables and any USB adapter (including external batteries). b. Configuration Full information on configuring the parameters of the units can be found in section Configuration c. -
Page 5: Physical Installation
ALS Tire BLE Install Guide 4. Physical Installation Figure 1 – Mounting (sensor – left, receiver – right) The sensor should be mounted in its final position using the mounting holes situated on the sides of the housing. For temporary installs we’ve successfully used 3M Dual-Lock tape, but extra care should be employed when using such a solution. - Page 6 ALS Tire BLE Install Guide Maximum Tire Width (mm) Mounting Distance (mm) Figure 2 - Channel assignment / sensor data order © Alsense Motorsport SRL...
- Page 7 ALS Tire BLE Install Guide Figure 3 - Visual Representation of channel assignments © Alsense Motorsport SRL...
-
Page 8: Mobile Installation
ALS Tire BLE Install Guide 5. Mobile Installation A. Harry’s Lap Timer or GPS/OBD Buddy (iOS / Android) Connecting to the device: 1. Download the latest version of the application. 2. If you have GPS/OBD Buddy, buy the Tires view add-on to be able to see the tire temperatures. - Page 9 ALS Tire BLE Install Guide Configuring the device: 1. Go to Administration: 2. Go to Sensor List: 3. Click on the Alsense sensor: 4. Modify the configuration and click Set. © Alsense Motorsport SRL...
-
Page 10: Operation & Charging
ALS Tire BLE Install Guide The Configuration is validated by the sensor, and if not valid it will not be applied. Check the Configuration section and the Appendix for more info about the valid values. 6. Operation & Charging Each sensor has a 250mAh battery that can be charged using the built-in connector. When in use, it allows for up to 15 hours of track time. - Page 11 ALS Tire BLE Install Guide increases the tire temperature. Suggested values depending on mounting distance: ● 50mm – 0.86 ● 150mm – 0.8 ● 200 – 0.77 Accepted values(1 is 0.01): 1-100 Sample Rate 10 Hz Sampling and reporting rate for the sensor.
-
Page 12: Troubleshooting / Faq
ALS Tire BLE Install Guide 9. Troubleshooting / FAQ Situation 1: Mobile application does not find the device a. Make sure the sensor has been fully charged. b. Bring the sensor near the receiver. Try resetting it using the magnetic override. -
Page 13: Support
ALS Tire BLE Install Guide Support Please make sure to check the downloads section of our support page as it provides the product’s datasheet and configuration files for the most common CAN dashboards/loggers. Extra help can be obtained using our built-in ticket support system or directly via phone. -
Page 14: Appendix A: Als Tire Ble
Bluetooth Communication Protocol V2.0 Updated 23.01.2022 Overview This document describes the communication protocol of the Alsense Tire Temperature Bluetooth low energy product. Device Naming The device name has the following convention: “ALS Temp BLE XXXXXX Y”. Where “XXXXXX” are the last 3 bytes of the MAC address and “Y”... -
Page 15: Current Protocol Version
ALS Tire BLE Install Guide Current Protocol Version The current protocol version is Version 2. Protocol Version 2 Temperature Service Temperature Characteristic Packet Field Size Description Values (bytes) Protocol The current protocol version. Version Battery Level The battery level in percentage. -
Page 16: Configuration Characteristic Packet
ALS Tire BLE Install Guide Configuration Characteristic Packet Field Size Description Values Default Values (bytes) Protocol The current protocol version. Version Number of The number of channels. Channels Sample Rate The sample rate in Hz. 1-10 (when waiting for movement the value is...
Need help?
Do you have a question about the ALS Tire BLE and is the answer not in the manual?
Questions and answers