Advertisement
Quick Links
Advertisement
Related Manuals for AquatiControl Technology ELC-800r
Summary of Contents for AquatiControl Technology ELC-800r
- Page 1 PERATION AND AINTENANCE ANUAL ELC-800r UTOMATIC ATER EVEL ONTROLLER AquatiControl Technology 3820 South Federal Blvd. Sheridan, Colorado 80110 Toll Free: 877.755.8817 Fax: 303.761.1499 www.aquaticontrol.com Serial No. _____________________ Model No. _______________________...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Introduction ................... 3 Installation ................. 4-5 Wiring Diagram ................6 Operation ..................7-8 Routine Maintenance ..............9 Troubleshooting ..............10-11 Warranty ..................12 - 2 - ACT 2009... -
Page 3: Introduction
INTRODUCTION The AquatiControl Technology (ACT) Model ELC-800r is designed to provide the most accurate and reliable automatic water level control for swimming pools, spas, fountains, and spray pads. All of the user-friendly features incorporated into the system were designed with the operator in mind. -
Page 4: Installation
The other end of the cable terminates inside the ELC- 800r. The interconnecting cable carries low voltage. Local codes may require the cable to be housed in conduit. Refer to www.aquaticontrol.com for sensing applications, drawings, and other product information offered by AquatiControl Technology. - 4 - ACT 2009... - Page 5 OLENOID ALVE The ELC-800r unit will actuate up to a 2” solenoid valve with a 24 VAC, 10 watt (max) supply, without the use of an auxiliary relay. AquatiControl Technology recommends an anti-water hammer or slow close solenoid valve. The power and ground cables should be directly connected to the ELC-800r terminal strip.
-
Page 6: Wiring Diagram
Wiring Diagram Input/Output Terminal Single Level Control Normal Level Sensor attaches to normal level sensor terminals (#’s 10,11,12) & Fill Valve attaches to fill valve terminals (#’s 1,2,3). Dual Level Control Normal Level Sensor attaches to normal level sensor terminals (#’s 10,11,12) & Fill Valve attaches to fill valve terminals (#’s 1,2,3). -
Page 7: Operation
OPERATION Once installation has been completed as described on the previous pages, open the water supply valve to sensor unit. If the water is not up to ideal level in the pool, manually adjust the water level to that point. After level is set and water is at normal operating water level, it is time to power the control unit. - Page 8 : No EFAULT LCD A (changes the contrast of the LCD) DJUST FOR VIEWING ANGLE LCD adjust can be set from 01 to 20. : 05 EFAULT (enables password protection of settings) ESET ASSWORD – No password required to change settings - Enter up to 8 digit (0-9) password If the password is forgotten the user can perform a master reset by turning the unit on while holding the up and down arrows (this will reset all settings to the default...
-
Page 9: Routine Maintenance
ROUTINE MAINTENANCE AquatiControl Technology’s Model ELC-800r controller is completely solid state and normally will not require any maintenance. ENSOR LEANING TANDARD The ½” PVC tube on the Standard Well Sensing Unit may need to be cleaned periodically. To clean the tube, isolate the sensor unit by closing the valve that supplies the water to it. -
Page 10: Troubleshooting
Level light does not come Wiring is incorrect in sensor Check wiring connection junction box Cable in ELC-800r Check wiring connection controller wired improperly Sensing unit is dirty Clean sensing unit Level light continually on Defective sensor... - Page 11 SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION Reset ELC by turning the Can not change settings Forgotten/wrong password power on while holding the up and down arrows ELC does not allow pump ELC is still in alarm and Press alarm reset button to turn on needs to be reset - 11 -...
-
Page 12: Warranty
WARRANTY AquatiControl Technology (ACT) warrants equipment of its manufacture and bearing its identification to be free of defects in workmanship and material. ACT’s liability under this warranty extends for a period of one year from date of delivery from our factory or authorized distributor. It is limited to repairing or replacing any device or part which is returned, transportation prepaid, to the factory within one year of delivery to the original purchaser, and which is proven defective upon examination.
Need help?
Do you have a question about the ELC-800r and is the answer not in the manual?
Questions and answers