Advertisement
Unit 1, 18 Francis Rd. Wingfield. South Australia. 5013
Ph: 1300 559 121
info@addabathroom.com.au
www.addabathroom.com.au
Installation guide for Add-A-Bathroom 8 panel flat pack tile look bathrooms.
FP800T; FP900T; FP1000T; FP1200T; FP1400T (with door opening)
Please read the entire guide prior to commencement of assembly or installation.
Note that this guide is provided for general information purposes only and should not be relied upon
without professional advice about your personal situation and installation requirements. As this guide
does not take personal circumstances or local regulations into account and as any installation is beyond
the control of Add-A-Bathroom, no responsibility is accepted nor warranty implied by Add-A-Bathroom
(or its affiliated entities) by the publishing or use of this guide.
Add-A-Bathroom flat pack bathrooms are manufactured in our modern production facilities and are
supplied ready for assembly and installation.
Follow this guide and your Add-A-Bathroom bathroom should give you many years of trouble free
service. No leaks, no cracks, no maintenance. If you have any queries please call us on 1300 559 121.
No specialised tools are required to install an Add-A-Bathroom flat pack bathroom. Installation of a
bathroom usually requires 2 competent people.
All plumbing and electrical work must be performed by appropriately licensed contractors.
Flat pack bathrooms are normally supplied as 8 panels with pre-drilled bolt holes and fasteners. Before
commencing installation open packaging and ensure all items are correct and in acceptable condition. No
claims regarding damage or missing components can be entertained after assembly commences.
(If you have sufficient access to receive and manoeuvre an assembled bathroom, the bathroom can be
supplied fully assembled ready for installation. Please contact Add-A-Bathroom for details.)
Line up, identify and label all panels so as to facilitate assembly. Check quantity of nuts, bolts, washers
etc. Ensure sufficient suitable sealant is available; this may be included with your bathroom depending
upon individual order.
Clean and maintain your new Add-A-Bathroom bathroom with domestic grade non-abrasive cleaning
agents. Walls may be polished with automotive or marine polishes suitable for use on fibreglass. Ensure
polishes, silicone washes, waxes and the like are kept away from any bathroom floor as such products
may be slippery.
ADD-A-BATHROOM Pty Ltd. Specifications and details subject to alteration without notice. (c) 2019
No warranty is expressed or implied by the publication or use of this guide. Page 1 of 8
Advertisement
Table of Contents
Related Manuals for Add-A-Bathroom FP800T
Summary of Contents for Add-A-Bathroom FP800T
- Page 1 Follow this guide and your Add-A-Bathroom bathroom should give you many years of trouble free service. No leaks, no cracks, no maintenance. If you have any queries please call us on 1300 559 121.
- Page 2 O. Apply the final ‘visible’ bead of sealant to joins, ensuring joins are void free. Refer to the sealant guide. Your Add-A-Bathroom is now assembled and ready for the installation of plumbing, electrical and accessories. ADD-A-BATHROOM Pty Ltd. Specifications and details subject to alteration without notice. (c) 2019...
- Page 3 (which would be unusual) all joins (other than the ceiling) should be so sealed. LEFT HAND SHOWER SHOWN ADD-A-BATHROOM Pty Ltd. Specifications and details subject to alteration without notice. (c) 2019 No warranty is expressed or implied by the publication or use of this guide. Page 3 of 8...
- Page 4 Where safety grab rails, seats etc are required to be fitted, contact Add-A-Bathroom as these may require additional measures, specific to the item. • If your bathroom was purchased with an electrical kit, have this refitted at this time or have your electrician fit electrical as required.
- Page 5 9. Allow the correct drying time as per the instructions on the tube. The MSDS for these products are available on request from Add-A-Bathroom, or B&N Products Pty Ltd. Step 2 Step 3 Step 5 ADD-A-BATHROOM Pty Ltd.
- Page 6 Add-A-Bathroom on 1300 559 121 or email info@addabathroom.com.au. Thank you for purchasing an ADD-A-BATHROOM product. ADD-A-BATHROOM Pty Ltd. Specifications and details subject to alteration without notice. (c) 2019 No warranty is expressed or implied by the publication or use of this guide. Page 6 of 8...
- Page 7 Braces (or framework) should be adhered to the bathroom walls not more than 600mm apart. ADD-A-BATHROOM Pty Ltd. Specifications and details subject to alteration without notice. (c) 2019 No warranty is expressed or implied by the publication or use of this guide. Page 7 of 8...
- Page 8 Product from the Add-A-Bathroom facility. To make a claim under this warranty, you must contact Add-A-Bathroom on 1300 559 121. All expense of claiming under the warranty will be borne by the person making the claim.
Need help?
Do you have a question about the FP800T and is the answer not in the manual?
Questions and answers