The UN-WPAMOUT is designed to protect large areas and can easily be installed on walls to provide a solid protection of the area while rejects interferences from birds and small animals due to “PET MASK”...
TAMPER – Whenever the cover is removed from Bracket or the device is tear off from the wall, • a Tamper signal will be transmitted to the UNii control panel. When cover will be returned, cancel the tamper signal on the UNii keypad.
The UN-WPAMOUT wireless outdoor detector is a robust detector which includes indication LED prism that can be easily observed from long distance. Having a back-metal bracket, the UN-WPAMOUT can be easily mounted to walls and poles using mounting screws or metal bands (both supplied)
Page 6
UN-WPAMOUT INSTALLATION INSTUCTIONS UNii Wireless outdoor PIR AM Front view Back view with battery LED Detector Batteries Cover Upper PIR Element Back Tamper Switch (Removal) Anti-Mask Sensor Lower PIR Element Dip Switches Front Tamper Switch (Opening)
12m detection distance (when installed at 1.5m above the ground surface). The UN-WPAMOUT has an internal rotating housing (which includes the 2 PIR elements) that can be adjusted vertically, so its 90° coverage may vary between 0° and 180°.
UNii Wireless outdoor PIR AM Pet Immunity The UN-WPAMOUT wireless outdoor detector can differentiate between pets and human bodies and alert accordingly by having PIR detection beams movement detection: A. Lower PIR element which is fixed to 12m range and 60 cm above ground level which helps avoiding pets’...
The UN-WPAMOUT performs best when provided with a constant and stable environment. To ensure suitable operation of the UN-WPAMOUT, type of ground should be one of the following: Asphalt concrete, Cement, Soil, Clay, Gravel, or Grass (mown).
(30 secs) 30 Sec during Warm Up and Learning The learning process should be completed within 30 seconds. UNii Control panel will indicate completion at the end of the process. Close the battery cover...
UN-WPAMOUT INSTALLATION INSTUCTIONS UNii Wireless outdoor PIR AM Detector Installation Important! Prior to installation, read “Select mounting location” section carefully. 1. Detector must be installed in such manner that the 2. The detector must be installed at height of 0.8m to intruder is most likely to cross the detection area 1.5m...
To change the detection beam direction, rotate the internal detection element housing to the desired direction. 7.2 Detection range setting The UN-WPAMOUT detection range may vary between 3m and 12m, while installed on 1.2m height above the ground surface Changing the detection range is achieved by sliding the upper detection element up or down:...
UN-WPAMOUT INSTALLATION INSTUCTIONS UNii Wireless outdoor PIR AM 7.3 Dip Switches Functions There are 5 DIP switches on the UN-WPAMOUT board that enable settings of following functions: ON = ENABLE SW1 PIR Sensitivity SW3 LED Indication SW4 Anti-Mask Activation SW5 Buzzer Audio...
Page 14
UN-WPAMOUT INSTALLATION INSTUCTIONS UNii Wireless outdoor PIR AM Switch 4 – ANTI-MASK ACTIVATION Future development: Use for Anti Mask function setting ** UP Position (ON) – AM feature enabled Down Position (OFF) – AM feature disabled MASKING CONDITION Future development:...
Changing the tamper switch state (by attaching / removing the detector to / from the bracket and/or the detector from the wall) will cause tamper transmissions. Check on the UNii keypad if it indicates a tamper alarm. Or check with UNii Manager software (at diagnostics) whether the detector indicates a tamper alarm.
UN-WPAMOUT INSTALLATION INSTUCTIONS UNii Wireless outdoor PIR AM Detection Method Double PIR Elements with optional Anti-masking feature Detection Pattern 90⁰ with 30 zones detection Communication UN-RF Two Way with unique serial ID Modulation Type GFSK Frequency 868MHz Events Transmission Alarm, Anti-Mask, Tamper, Supervision, Low Battery...