Table of Contents
Summary of Contents for culiau Customizer
- Page 1 USER MANUAL IMPORTANT: Read before using Customizer™ Engraving Pen Contact us for Consumer Information Customer Service: support@culiau.com Website: www.culiau.com Instagram: www.instagram.com/culiaustore/ Address: 312 W. 2nd St #1490 Casper Postal code: WY 82601...
- Page 2 AND SPECIFICATIONS WHAT IS IN THE BOX? OPERATING INSTRUCTIONS CUSTOMIZER™ ENGRAVING PEN INTRODUCTION 05 - 06 USING THE ENGRAVING PEN HOW TO USE THE CUSTOMIZER OPERATING SPEEDS VARIABLE SPEED DIAL HIGH-PERFORMANCE MOTOR BATTERY CHARGE CONDITION INDICATOR LIGHTS ASSEMBLY OPERATING SPEEDS...
-
Page 3: Work Area Safety
GENERAL ENGRAVING PEN SAFETY WARNINGS WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE • Always turn off the tool before REFERENCE changing accessories, changing collets, or servicing the tool. -
Page 4: Kickback And Related Warnings
these instructions to operate it. Keep cutting accessories sharp and Engraving pens might be dangerous in clean. Properly maintained cutting the hands of untrained users. accessories with sharp cutting edges are less likely to bind and are easier to MAINTENANCE OF THE control. -
Page 5: Functional Description And Specifications
FUNCTIONAL DESCRIPTION AND SPECIFICATIONS Customizer™ Engraving Pen Full Copper Chuck Allen grub screw Power button / Gear adjustment buttom Electroplating Alloy Body USB-C Charging Port Display (Page 08) Mini Spanner Slot Electrical source USB Charging Transfer speed 5000 - 25000 r/min... -
Page 6: What Is In The Box
WHAT IS IN THE BOX? Four engravings pen bits USB Type - C Charging cable Hex key Customizer™ Extra Allen Engraving Pen grub screw Customizer™ Engraving Pen... - Page 7 Allen grub screw on the 1) Open the box. chuck. 2) Take out the Customizer and the 7) Select a bit and put it into the chuck. plastic tray to get the pieces below it. 8) Tighten the Allen grub screw with the 3) Grab the USB type-C Charging Cable hex key.
- Page 8 Figure A For best control in close work, grip the engraving pen like a pencil between your thumb and forefinger. The first step in learning to use the Instead, lower the spinning accessory Engraving Pen is to get the “feel” of it. lightly to the work and allow it to touch Hold it in your hand and feel its weight the point at which you want cutting (or...
- Page 9 ASSEMBLY WARNING: Always turn off the engraving pen before changing accessories. LOOSEN Loosen the Allen grub screw with the Hex Key Insert the bit you require TIGHTEN Tighten the Allen grub screw with the Hex Key...
-
Page 10: Operating Speeds
OPERATING SPEEDS To select the right speed for each job, use TO TURN THE TOOL “OFF” push the a practice piece of material. button four times. It will go from the The tool is switched on by pushing the highest rotary speed, until the lowest, green button on the display and it will finally turn off. - Page 11 3 “side to side” lights – battery charge is heavy use, this most likely indicates that too low to run tool.Recharge the battery. the Li-Ion cells are near their maximum 1 red light – battery is too hot for use. operating temperature, and the battery Turn tool off and let the battery pack should either be changed or...
- Page 12 The products it herein. describes are subject to change without Culiau shall not be liable for any dama- prior notice, due to the manufacturer’s ges, losses, costs or expenses, direct, continuous development program.
- Page 13 Copyright © 2021 Culiau. All Rights Reserved 312 W. 2nd St #1490 Casper, WY 82601 - support@culiau.com...