Advertisement
III
Product List and Installation Explosion Diagram
Please check carefully according to the following list after unpacking the packing
case. If any omission is found, please contact our company or local agent in time.
Product List
No.
Name
1
Outer cover plate
2
Inner cover plate
3
Inner bottom plate
4
Inner rubber pad
5
Lock body
6
Screw kit
Board buckle plate
7
and case
Anti-theft door
8
buckle plate
9
Card (optional)
List of screw packages (40~90 door thick)
No.
Name
Cross countersunk self-tapping
1
screw
2
Cross countersunk screw
3
Cross pan head screw
Cross pan external tooth two
4
combined screw
Cross pan external tooth two
5
combined screw
Cross pan external tooth two
6
combined screw
7
Square bar
8
Counter-lock bar
9
Allen wrench
10
Square bar guide seat (plastic)
11
Cover plate screw hole
12
Locating pin
13
Connecting pipe
Installation Explosion
Inner bottom plate
Inner rubber pad
Square bar
Outer cover
plate
Lock body
Connecting pipe
Note:
This part is only used for installing the locating square bar, and
it shall be removed when installing the inner cover plate
Number of locks per
Remarks
set
1
1
1
1
1
See the table below
1
for details.
1
1
2
Quantity
Remarks
6
ST4.2X20 for wooden door installation
8
M5X10 for iron gate installation
M5X15 inner cover plate is fixed to the
4
inner bottom plate
M5X35 is suitable for 50~70mm door
3
thickness
M5X65 is suitable for 75~90mm door
3
thickness
M5X25 is suitable for 40~50mm door
3
thickness
1
1
1
For fixing external handle
For inner bottom plate mounting guide
1
(must be used)
2
1
For fixing the counter-lock square bar
3
For fixing inner and outer plates
Diagram
Cover plate screw
Inner cover plate
Battery compartment
Bottom plate screw
Tapping screw
IV
Installation Instructions
1. Door direction confirmation before installation
The smart door lock is suitable for four kinds of doors with left outer opening, left inner
opening, right outer opening and right inner opening. Determine the direction of the
handle according to the left or right opening, and determine the direction of the oblique
bolt according to the inner or outer opening. As shown in the following figure
Right inner opening
2.Handle direction change
Use an Allen wrench and a Phillips screwdriver to unscrew the Allen screw and the
handle fixing screw, pull out the handle moderately, rotate 180° to the correct position,
and then screw back the screw. Rotate along the right outer opening and right inner
opening handle directions to position 1, and along the left inner opening and left outer
opening handle directions to position 2. The specific steps are shown in the following
figure
Outer cover plate
B: After unscrewing the two
screws with a screwdriver,
turn the handle 180° to the
key hole surface to the
correct position and then
screw back the screws.
Inner cover plate
C: Turn on the safety
button, unscrew the two
screws with a screwdriver,
rotate the handle 180° to
the correct position and
then screw back the
screws.
3. Lock body oblique bolt direction change
The direction of oblique bolt for right outer opening and left inner opening is as shown
in fig. 1; The direction of oblique bolt for right inner opening and left outer opening is as
cover
shown in fig. 2. The specific steps are shown in the following figure
Lock body
Caution
1.
Before installation, be sure to determine the direction of door opening and switch the handle and
oblique bolt according to the installation instructions.
2.
After the whole lock is installed, open the sliding cover of the front cover plate, enter any 6-12 digit
password, or enter any line to imitate the unlocking action. If the front handle is pressed down when
the LED indicator light is on and the green light is on, the installation is completed if the lock body
oblique bolt and the main bolt can be normally controlled. Remember that no one is allowed to close
the door outside the door until the installation is confirmed to be completed
Left inner opening
Right outer opening
Direction of external
External handle
handle for right opening
direction change
Internal handle
Direction of internal
direction change
handle for left opening
Lock body Direction
Figure 1
change
Use a Phillips
screwdriver to
unscrew the
lock body panel
screw. After the
panel is
removed, rotate
the oblique
tongue180° ,
then install the
panel into the
lock body, and
lock screw
Left outer opening
Direction of external
handle for left opening
Direction of internal
handle for right opening
Figure 2
Advertisement
