Advertisement
Quick Links
Auto water changer
)
(Pro version
System connection -----------
Instruction for A.T.O.
Instruction for A.W.C. --------
Child lock and others
Manual
Ver.1.0
P1
-----------
P2-3
--------
P4
P6-P8
--------
--------
P15
--------
P16
---------
P17
----------
P18
Advertisement
Related Manuals for Smartreefs Tosta-PRO
Summary of Contents for Smartreefs Tosta-PRO
-
Page 1: Table Of Contents
Manual Auto water changer (Pro version Ver.1.0 System connection ----------- Installation Notes ----------- P2-3 Instruction for A.T.O. -------- Instruction for A.W.C. -------- P6-P8 Advanced settings -------- P8-P14 Instructions for use -------- Child lock and others -------- Show code meaning --------- Troubleshooting ----------... -
Page 2: System Connection
System connection [Universal] Installation Notes An anti-siphon · An anti-siphon device must be installed above the drainage pump, other wise non- stop drainage may occur ; · If the water level in the bucket is higher An anti-siphon than the water level in the area where the main controller is installed, an anti-siphon device should also be installed above the pump in the bucket. - Page 3 Installation and A.T.O.function Installation of the host · The installation site must be cleaned before installation. Large algae or dirt may cause Installation 1. Install the host on the section where the abnormal sensing. steps water level in the fish tank can change, and make the current water level near the "LOW"...
- Page 4 · If the water level drops quickly after · During standby: The current time is displayed Interface exceeding the HIGH level line, there may be Precautions and can be changed in settings. introduction water droplets remaining on the sensor · With temperature function on standby: Time head, which may cause a false alarm that the and temperature are displayed alternately.
- Page 5 · During calibration, the system will add water Setup 1. Press and hold the Set button for 5 seconds to Notice first, then drain water, and finally enter and calibration enter the setting mode, and F1 is displayed on exit the water for a period of time. If you find the screen.
-
Page 6: Advanced Settings
Advanced settings (recommended) · Project location: F1S4-A-XXXX Intermittent · You can set the required inter val for changing the water in minutes. For example, if Switch · Press and hold the Set button for 5 seconds to you set this parameter to 60, it means categor y enter the setting mode. - Page 7 Advanced settings (optional) [S1 -AWC] · Project location: F1S6-XXX Timeout · Modify tolerance in order : water in, water parameter · Project location: F1S5 out, and simultaneously. Option On: Turn on temperature linkage during Temperature · Default: 200% / 100% / 150% linkage water change ·...
- Page 8 · Project location: F2S4 Advanced settings (optional) [S4 -SYSTEM] One-click · You can set the maximum running protection top up time for one-key full function. protection System time · Select this function when the water level is lower · Project location: F4S1 than the Low water level, the system will ·...
-
Page 9: Instructions For Use
Instructions for use [related to A.W.C.] Instructions for use [indicator] · The water level indicator flashes for 2 · During calibration, as long as the inlet and outlet Water level seconds after it is on for 2 seconds, please indication pumps are working properly and the water level is Calibration change the installation position to avoid... -
Page 10: Show Code Meaning
· The buzzer alarm will be triggered when the Level · Star: Water is being poured into the container A.W.C.Related monitoring water level reaches the HIGH level. Done: automatic calibration is complete. · The alarm will be automatically cancelled · Hig: The water level is too high when starting when the water level returns to normal. -
Page 11: Troubleshooting
Troubleshooting suggestions A.T.O. fault · It is usually caused by water shortage or pump failure. Please check the water source. If the pump does not work, please replace the pump. A.W.C. fault · If the water level is still too low after three consecutive water refills, an A.T.O. - Page 12 *The temperature probe must not be completely submerged in water, and the water level should be below the highest water level line marked on Water level indicator the probe. Smartreefs 8 8 8 8 Digital display ·The temperature probe is not hot-swappable. Pause Function A.T.O.
- Page 13 Water level indicator the probe. ** A physical safety device must be installed on the floor (lower ground) Smartreefs near the fish tank . · The temperature probe is not hot-swappable. 8 8 8 8 Digital display ·...
Need help?
Do you have a question about the Tosta-PRO and is the answer not in the manual?
Questions and answers