Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FITWAY FW-500IC
Summary of Contents for FITWAY FW-500IC
- Page 1 USER MANUAL FW-500IC...
-
Page 2: Safety Guidelines
SAFETY GUIDELINES Regular maintenance of the bike should be performed and is essential to keep your Indoor Cycle in top operating condition. Without preventative maintenance, normal wear and tear may cause cumulative effects, such as misalignment or early replacement of parts. Once assembled, please inspect to make sure that all hardware parts such as bolts, nuts and washers are positioned and tightened correctly. -
Page 3: Exploded View
EXPLODED VIEW... -
Page 4: Parts List
PARTS LIST Part Part Name Specification Main Frame Seat Post Handlebar Post Rear Foot Tube Front Foot Tube Seat Slider Handlebar Washer Ø30*Ø10.5*4T Seat Horizontal Adjust Knob M10*Ø52 Match 25*50*1.5T Flat Oval Seat Post Plug Tube Seat PJ Belt Wheel Ø200×20(With magnet) PJ Belt 6PJ 50.5 inches... - Page 5 Screw M6*40L Chain Cover A Chain Cover B Chain Cover B Gland Decorative Cover Phone Holder Left Sweat Cover Right Sweat Cover Small Chain Cover Flywheel Ø420×25W×6.5KG Flywheel Left Decorative Cover Ø386*Ø60*2.5T Flywheel Right Decorative Cover Ø386*Ø60*2.5T Flywheel Spindle M10*P1.0*139L Flywheel Distance Sleeve Ø14*Ø10.2*19.5L Flywheel Distance Sleeve...
- Page 6 Circuit board Regulator Button Battery Hexagon Socket Cap Screw M8*10 8.8 Grade Washer ExternalØ16*InternalØ8*2T Hexagon Flat Head Screw M10*16 8.8 Grade Washer ExternalØ20*InternalØ10.1*1.5T Cap Nut Hexagon Thin Nut M10*1.0*4T Hexagon Flange Nut M10*P1.25*8T 8.8 Grade Hexagon Flange Nut M10*1.0，8.8 Grade Hex Nut M10*8T Base Leveler...
- Page 7 Handlebar Plug Handlebar Fix Plate Crosshead Self-tapping Tail Screw ST4*11L Transit Wheel Hexagon Flat Head Screw M8*35 Nylon Nut Nylon Nut Washer φ6xφ16x2T Cross Head Self-Tapping Screw - small head ST4*11 Hexagon Bolt M6×16 Hexagon Flange Nut Right Crank Decorative Cover Left Crank Decorative Cover Hexagon Flat Head Screw M6*12...
- Page 8 ASSEMBLY INSTRUCTIONS...
- Page 9 STEP 1: Assemble Front and Rear Foot Tubes Attach the Rear Foot Tube to the Frame with Hexagon Flat Head Screw (54) and Washer (55). Next, attach the Front Foot Tube with the same way with the same hardware.
-
Page 10: Step 2: Attach The Pedals
STEP 2: Attach the Pedals Gently insert the Left Pedal into the Left Crank, make sure the pedal is at a 90° Angle to the crank. Slowly rotate the Left Pedal (18) into the left crank using Open Spanner Wrench (A) towards the direction of Handlebar (counterclockwise). -
Page 11: Step 3: Attach The Seat
STEP 3: Attach the Seat Slide the Seat post (2) into the Frame (1) and tighten it with Seat Vertical Adjust Knob (68). Then connect the Seat Slider (6) to the Seat Post (2), tighten it with Seat Horizontal Adjust Knob (9) and Washer (8). Finally, attach the Seat (11) to the Seat Slider (6) by using Open Spanner Wrench (A). - Page 12 STEP 4: Attach the Handlebar Post/Handlebar/Tablet Holder/Console 1.Connect the Handlebar Post (3) to the Frame (1). Tighten the Handlebar Vertical Adjust Knob (97). Attach the Handlebar (7) to the Handlebar Post (3) with Hexagon Socket Cap Screw (52) Washer (53). 2.
- Page 13 SAFETY CHECK, TRASPORT & MAINTENANCE 1. Before using your Indoor Cycle, please kindly check that all the moving parts (screws, nuts, adjustment levers, etc.) are firmly tightened and secured. Please check your equipment regularly. If any damaged parts are found, discontinue use, and replace them immediately. Do not exercise with your Indoor Cycle until relevant worn parts are repaired or replaced.
-
Page 14: Computer Operation
COMPUTER OPERATION POWERING ON AND OFF The computer turns on when any button is pressed or when you start cycling. The computer will turn off automatically after 4 minutes of no use. MODE The computer can be set to allow you to work towards a specific goal. Press the MODE button to cycle through the following stats: SPEED / TIME / DISTANCE / CALORIES / TOTAL DISTANCE / PULSE Note, to use the pulse function, a Polar®... - Page 15 CONGRATULATIONS Thank you again and congratulations on your purchase of this FitWay Indoor Cycle. Should you have any questions or concerns please contact us at: Support@FitWayEquip.Com Full Warranty details can be obtained at: fitwayequip.com -or- By emailing us at: support@fitwayequip.com...