Advertisement
WARNINGS
Following instructions must be consulted in order to obtain a correct installation,
use and maintenance of product, as well as ensuring your safety.
Still retain this documentation for future reference, even for those who will later
work on the lamp for any reason.
FEATURES
Industrial LED projector made with an aluminum structure, a highly polished
aluminum reflector and tempered closing glass. The overall dimensions
is between 395mm and 575mm in height and 370mm and 460mm in width
(diameter).
• LED light source
• T° of colour 4000K (Neutral White) or 5000K (Cold White)
• Absorption 0,65A (THOR 150), 1,1A (THOR 250), 1,45A (THOR 330)
• Frequency: 50-60 Hz
• Input voltage 90-305 Vac
• Consumption 150W (THOR 150) , 250W (THOR 250), 330W (THOR 330)
• Appliance with isolation class I
• Max nominal ambient temperature: +80°C
• Min nominal ambient temperature: -40°C
• IP Protection class: IP65
• Use of heat-resistant power cables, interconnection cables or external wiring
till +90°C
Features of the power connector
• Number of poles 3
• Contact marking L - N - E
• Type of connection screw (M3 - max. 0.5 Nm)
• Operating current max. 32A
• Operating voltage max. 450V AC
• Protection against solid/water (IP) IP68 (50m,1h)/IP69K
• Corrosion resistance Salt mist, 1.000 ore, 5% salt solutions, 35°C EN60068-2-
11:2000, Test Ka (168h)
• Wire cross-section min. - max. (Stranded cable) 0.5 mm - 4.0 mm
• Wire cross-section min. - max. (Solid cable) 0.5 mm - 4.0 mm
• Cable diameter min. - max. 8.0 mm - 17.0 mm
SAFETY RULES
Always switch off the fixture before carrying out any cleaning.
Before taking any action on it make sure it has completely cooled.
Fixture suitable for installation on normally inflammable surfaces.
Designed for direct illumination of horizontal and vertical surfaces.
LED light source: it is recommended not to fix the beam to avoid possible
permanent damage to the retina.
Device suitable for indoor and outdoor use. The light source of this appliance
is not replaceable; when the light source reaches the end of life, the whole
luminaire must be replaced.
Electrical part consists of a stabilized power supply: built-in protection
circuit shuts down the device in case of open circuit, short circuit, overload or
overheating; the power supply may not be turned on even after the fault. In this
case, contact the manufacturer.
Conductor cross section min. min 0,5 mmq - max 4mmq.
Operating temperature: min. -40°C max. +80°C.
The luminaire must be positioned in such a way that a prolonged observation of
the luminaire is not possible at a distance of less than 4 meters.
Notes for the disposal of the device, see RAEE standards.
HOW TO USE
Open the box, extract the fixture carefully and store up the packaging.
Fix the lamp to the ceiling, hooking it with the special carabiner. Additional holes
are available on the lamp bracket for rigid fixation to other brackets or beams.
In the equipment there is a TECNHO Joint connector model THB.400.D1N,
that must be connected to the output cable from the lamp, paying attention to
connect the earth cable in the appropriate seat inside the connector, marked
precisely with the ground symbol; the conductors must be stripped of 5mm to
allow correct tightening inside the connector; then it's possible to connect the
TECHNO joint connector to the power supply cable (220Vac).
If the external flexible cable of this appliance is damaged, it must be replaced
exclusively by the manufacturer.
Do not cover the device with plastic sheets, cloths, tissues cause it has to
dissipate the heat produced by the light source. For cleaning and maintenance
always use a damp cloth without any solvents or acids. For your safety, do not
attempt to modify the unit.
The information contained in the following documents are subject to change
without any notice by the company. The company guarantees the conformity
of the products with the applicable European safety and EMC. We accept no
responsibility for any damage to the product, to things and/or people, due to
improper installation and/or because of changes made to the device, using
accessories and/or electrical/electronic components are not suitable. It's strictly
forbidden any reproduction, even partial, of the information contained in this
leaflet.
The reproduction, even partial, of the contents of this leaflet is strictly
forbidden.
Advertisement
