Related Manuals for Early Settler 90009804
Summary of Contents for Early Settler 90009804
- Page 1 Byron AC Fan Matt Black /Matt White Byron SKU 90009804 & 90015408 90009804 90015408 ML-51-02 Visit earlysettler.com.au or call 1300 653 969 to contact our customer service team. 1 / 12...
- Page 2 Downrod Canopy installation Blade 6. Attaching an accessory light kit Wall 10. Trouble shooting Electrical Shock Warning :There are no DIY servceable parts contained in this product. Please engage a licensed electrician to carry out installation and / or undertake any servicing. Visit earlysettler.com.au or call 1300 653 969 to contact our customer service team.
- Page 3 1. Turn off power before assembly & disassembly. To avoid electrical shock, connect earth / ground wire first, followed by neutral wire and active wire last. For disassembly, disconnect active wire first, followed by neutral wire and ground / earth wire last. 2.
- Page 4 LIGHT Blade 5pcs Wall Control 1set Blade holder screw 10 psc Blade screw 15 pcs Spring washer 10 pcs Round metal washer 15 pcs Visit earlysettler.com.au or call 1300 653 969 to contact our customer service team. 4 / 12...
- Page 5 4. Downrod & Coupling installation 1 ) Thread wiring from fan motor through downrod. Visit earlysettler.com.au or call 1300 653 969 to contact our customer service team. 5 / 12...
- Page 6 Blade Assembly 1) Use the 3 blade screws and washers to secure the blade to blade holder. 2) Now put the blade holder under the lower motor housing and use the 2 blade holder screws and washers to secure the blade holder to the motor housing.
- Page 7 Fig1: Decorative Cap Green-yellow Blue Fig2: Screw Screw light Assembly Kit Lampholder Glass Bulb Fig3: Fig4: Blue Green-Yellow Visit earlysettler.com.au or call 1300 653 969 to contact our customer service team. 7 / 12...
- Page 8 Wiring diagram of mounting bracket terminal & wall control terminal. GREEN/YELLOW EARTH ORANGE BLUE SUPPLY NEUTRAL BROWN ACTIVE TERMINAL BLOCK WALL MOUNTING BRACKET CONTROL TERMINAL BLOCK MOTOR WALL CONTROL LIGHT WINRE 1) Put the hanger ball into hanger bracket, turn the down rod until the groove of the hanger ball locates into the lugs of hanger ball plate (in hanger bracket).
- Page 9 Wall PPLY NEUTRAL ACTIVE WALL CONTROL TERMINAL BLOCK WALL CONTROL LIGHT Wall n rod until the groove plate (in hanger bracket). bracket lugs. IMPO 1. Please 2. Please OFF: turn off the fan installe high speed 3. To avoi MED: medium speed turned LOW:...
-
Page 10: Important Points To Remember
Ceiling Fan Wall-Mounted Control Installation Instruction IMPORTANT POINTS TO REMEMBER: 1. Please read this instruction and save it for further use. 2. Please note that all fixed wiring appliances should be installed by a qualified electrician. 3. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box or circuit panel before wiring. - Page 11 TROUBLE SHOOTING: A bal WARNING: over t CEILING FAN MUST BE SWITCHED OFF AND ISOLATED BEFORE COMMENCING ANY TROUBLE SHOOTING NOIS When WOBBLE / BALANCE: and fr Please note that all ceiling fans are not the same, even fans of the chang same model, some may move more or less than others.
-
Page 12: Balancing Kit
BALANCING KIT: A balancing kit may be required to balance the ceiling fan at some stage if it becomes unbalanced over time. Please refer to the instructions contained with the balancing kit for details of how to use. NOISE: When it is quiet, especially at night, you may hear occasional small noises. Slight power fluctuations and frequency signals superimposed in the electricity for off-peak hot water control, may cause a change in fan motor noise.
Need help?
Do you have a question about the 90009804 and is the answer not in the manual?
Questions and answers