User Manual of Fiber Laser Chiller Catalogu e Introduction ------------------------------------------------------------------------------------- 4 Warning notices----------------------------------------------------------------------------------5 1 s u m m a r i z e ----------------------------------------------------------------------------------- 8 2 service conditions ----------------------------------------------------------------------------- 8 2.1 environmental requirement ------------------------------------------------------- 8 2.2 Medium requirements------------------------------------------------------------------9 ...
Page 3
User Manual of Fiber Laser Chiller 8.1 Summer dust ------------------------------------------------------------------------------- 19 8.2 Winter antifreeze --------------------------------------------------------------------------- 19 8.3 current maintenance ---------------------------------------------------------------------- 20 9 F a i l u r e a n a l y s i s a n d e l i m i n a t i o n ---------------------------------------------- 21 10 circuit diagram-------------------------------------------------------------------------------22 ...
User Manual of Fiber Laser Chiller foreword Thank you for your trust in our company and choose to use our fiber laser chillers. In order to enable you to better understand and use our products, make them play the best results, and provide you with complete after-sales service, please contact us Read this manual carefully before use, and you can refer to this manual if you have any doubts in the process of using the product.
User Manual of Fiber Laser Chiller Warning notices In order to ensure your personal safety and avoid property damage, you mus t pay attention to the warnings in the instructions of our company. The wa rnings are listed below according to the level of danger, but not limited to the following list. General knowledge of electricity use and safety reg ulations should also be followed. Be sure to take safety precautions, otherwise it will cause death or Danger serious bodily injury Prompt project operation specification Reminder mark Handling, installation, piping, electrical, operation, Please be operatedby maintenance, overhaul and other operations must be professional...
Page 6
User Manual of Fiber Laser Chiller Do not let the equipment water, water, or there Water proof may be a short circuit and electric shock risk. Be sure to take safety precautions, otherwise it will cause death or serious Alarm bodily injury Reminder mark operation specification...
Page 7
User Manual of Fiber Laser Chiller a) It is forbidden to use it in special environments such as high temperature, humidity, and strong electromagnetic interference; operating environment b) The equipment must be installed in a place where there is no direct sunlight and away from fire sources.
User Manual of Fiber Laser Chiller summarize This product is a cooling device designed and manufactured for laser cutting, laser welding, laser engraving, laser marking, laser printing and other laser processing equipment. It can provide two cooling media with stable temperature for the above application scenarios, one is low temperature The cooling liquid cools the fiber laser, and the other is room temperature cooling liquid, which cools the fiber laser cutting head.
User Manual of Fiber Laser Chiller relative humidity:≤90%; elevation :≤3000m; The relationship between the cooling medium temperature and the ambient temperature is shown in Fig.2 介 质 温 度 Normal operating range medium temperature ℃ ℃ e n v i r o n m e n t t e m p e r a t u r e ℃ (a)Pure softening water operating range 介...
G -Water filling filter (water free filter omitted) Q -Stainless steel coil evaporator Matched laser power Hanli industrial chiller category, HL represents cutting machine, Sch represents hand- held welding machine For example: HL-3000-QG2/2 means a laser cutting machine with a matching laser power of 3000W, using a stainless steel coil evaporator, a filter installed in the water circuit, and dual temperature two-way water supply.
Page 12
User Manual of Fiber Laser Chiller It must be installed horizontally and cannot be tilted. As shown in Figure 3, anchor bolts should be used for equipment without casters, and the universal wheels should be locked for equipment with ...
User Manual of Fiber Laser Chiller n o t p u t t h e e q u i p m e n t d i r e c t s u n l i g h t F i g 5 E q u i p m e n t i n s t a l l a t i o n e n v i r o n m e n t...
User Manual of Fiber Laser Chiller e l e c t r i c a l c o n n e c t i o n Please refer to the wiring mark of the chiller when wiring. Recommended reference standards for power cord diameter selection Rated current / A ≤5 ≤10...
7.2 C o n t r o l l e r p a n e l i n t r o d u c t i o n At present, there are three kinds of controllers for Hanli fiber laser chillers. Most models use split digital tube controllers, as shown in Figure 9.
User Manual of Fiber Laser Chiller 7.2.1 s p l i t c o n t r o l l e r p a n e l F i g . 9 7.2.2 Introduction of the integrated controller panel real-time temperature setting temperature i n t e g r a t e d F i g .
User Manual of Fiber Laser Chiller 7.2.3 Introduction of the split controller panel 7.3 s t a r t i n g u p d i s p l a y After the integrated controller device is powered on, the PV and SV areas will display the software version information, and enter the temperature display state after about 7 seconds After the split controller device is powered on, the display window will display the software version information (Fxx/v100/A00), and it will enter the temperature display state after about 7 seconds.
User Manual of Fiber Laser Chiller 7.4.2 S p l i t c o n t r o l l e r t e m p e r a t u r e d i s p l a y Display window default display of low temperature water temperature measurement (L.XX.
User Manual of Fiber Laser Chiller maintaining For maintenance,equipment must be shut down, cut off the power supply, and can only be operated after 3 minutes, otherwise there will be a risk of electric shock. When the ambient temperature is lower than 2°C, the internal water must be drained when the machine is shut down for a long time.
User Manual of Fiber Laser Chiller Table 1 Correspondence between different volume ratios of ethylene glycol and freezing point volume ratio/% freezing point freezing point freezing point volume ratio volume ratio /℃ /℃ /℃ -0.6 26.0 -13.0 51.9 -41.0 -1.3 28.0 -15.0 53.9...
Page 21
User Manual of Fiber Laser Chiller Test insulation resistance, insulation resistance≥5MΩ; Check the ground resistance, ground resistance ≤4Ω; Carry out the capacitance value test on the capacitors of the compressor and the fan, and the capacitance value attenuation ...
Page 22
User Manual of Fiber Laser Chiller A: Water replenishment (to the top low temperature water and standard area of the liquid level) Water level A: Insufficient water tank level normal temperature water heating switch alarm A: The condenser is dirty A: Clean up the dust and blocked B: Check for leaks...
Page 23
User Manual of Fiber Laser Chiller K M 1 K M 2 K M 3 K M 4 1 点 2点 3点 P h a s e L o w p u m p compr normal t e m p e r a t u r e s e q u e n c e temperature...
User Manual of Fiber Laser Chiller F i g u r e S p l i t c o n t r o l l e r c i r c u i t d i a g r a m 11 Transport and storage 11.1 T r a n s p o r t r e q u i r e m e n t s 1.
User Manual of Fiber Laser Chiller Storage environment conditions, temperature: 0~60℃, relative humidity: ≤90%. Other instructions 12.1 S e r v i c e s u p p o r t 12.1.1 Warranty Within 24 months from the date of purchase of the product by the company, if it is obviously a failure caused by a design defect or a quality problem caused by the manufacturing, the company provides free repairs and replacement parts.