Advertisement

MOTORIZED TREADMILL
USER MANUAL
Please ensure you read the User Manual and Safety Instructions carefully before operating this machine.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KBR-JK8808 and is the answer not in the manual?

Questions and answers

Summary of Contents for Genki KBR-JK8808

  • Page 1 MOTORIZED TREADMILL USER MANUAL Please ensure you read the User Manual and Safety Instructions carefully before operating this machine.
  • Page 2: Table Of Contents

    CONTENTS TION 1. CAUTION 2. SAFETY NOTICE 3. CAUTION DURING USE 4. TECHNICAL SPECIFICATION 5. ASSEMBLY INSTRUCTIONS & BOX CONTENTS 6. CONTROL PANEL & OPERATING INSTRUCTIONS 7. FOLDING UP AND SETTING DOWN 8. LUBRICATING THE BELT WITH SILICONE OIL 9. RUNNING BELT ADJUSTMENT 10.
  • Page 3: Caution

    1. CAUTION To avoid injury please read this manual carefully before operating this machine. TION ◼ NEVER attempt to mount the treadmill while the running belt is moving. ◼ NEVER step off the treadmill while the running belt is moving. ◼...
  • Page 4: Safety Notice

    2. SAFETY NOTICE ◼ This machine is not suitable for children under 14 years of age. TION ◼ Use the treadmill only for its intended use as described in this manual. ◼ Children, elderly users and pregnant women are advised NOT to use the treadmill. ◼...
  • Page 5: Technical Specification

    4. TECHNICAL SPECIFICATION TION Product Name Treadmill Motor Power 2.0HP Voltage 220-240V Frequency 50Hz Speed Range 1-12km/h Maximum User Weight 120KG 5. ASSEMBLY INSTRUCTIONS & BOX CONTENTS TION Assembly Instructions :...
  • Page 6 Please check that all contents are present before assembling this machine: 1. Two person take out the machine from carton,pull up the support frames and use the 2 knob(in accessory bag)fix the support frame with the base. 2. Make the computer handrail bar in horizontal direction,and insert the bolt into the support frame hole.
  • Page 7: Control Panel & Operating Instructions

    6. CONTROL PANEL & OPERATING INSTRUCTIONS TION 1. Plug the power line and turn on the red power switch at the back of the machine. 2. Place the emergency stop safety key on the front of the console. Clip the other end of the safety key onto your clothes and stand on the running belt facing the console.
  • Page 8: Folding Up And Setting Down

    7.In case of emergency, please pull out safety key. The machine will stop very slowly. 8.To stop the machine you can also press the " ". 7. FOLDING UP AND SETTING DOWN TION ⚫ Take off the bolt on the computer to fold the computer. ⚫...
  • Page 9: Lubricating The Belt With Silicone Oil

    8. LUBRICATING THE BELT WITH SILICONE OIL TION Lift up the running belt. Then put silicone oil straight on to the running board. Now start the machine and run for 3 minutes without any load on the belt (i.e.do not stand on the machine).
  • Page 10: Running Belt Adjustment

    9. RUNNING BELT ADJUSTMENT TION (1) Running belt deviates to left - Start the machine, set speed at 2-3Km/h without a load on the belt, use Allen key to turn the screw 1/4 turn(see fig1). Then allow the machine to run without a load for 1-2 minutes.
  • Page 11: Overiew Drawing

    11. OVERIEW DRAWING PARTS LIST Serial Part Name Spec unit Computer board Upper computer cover Bottom computer cover Upper handrail bar Q235 Compression spring Pin pull ring...
  • Page 12 Support frame Q235 Right motor cover Power line Switch Overload protector Cross head tapping screw ST4*12 Front motor cover knob Countersunk cross screw M12*20 self-locking nut Wheel Cylinder head hexagonal screw Foot pad Cross belt pad self-drilling screw ST4.2*16 Left motor cover Motor Quintuplet belt Bottom motor cover...
  • Page 13 Cylinder head hexagonal screw M6*55 Right end cap Running board Countersunk head hexagonal screw M8*40 Side strip Edgings Running belt Upper motor cover Cover Heartbeat key Safety key IPAD holder...

Table of Contents

Save PDF