Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for uandksound T Series
Summary of Contents for uandksound T Series
- Page 2 Beware: To reduce the risk of electric shock, never remove parts of the front cover (or back cover) that require no user service. Please ask professional maintenance personnel for repairs. WARNING: To reduce the risk of fire or electric shock. Do not expose the device to rain or moisture.
-
Page 3: Power Cable
7. Do not block any ventilation holes and follow the manufacturer's instructions for installation. 8. Do not install this equipment near any heat source such as radiators, heaters, stoves, or other equipment that generates heat, including amplifiers. 9. Do not damage polarized or grounded plugs for safety purposes. The polarized plug has two pins, one of which is wider. - Page 4 They can really restore the sound in the sound material. The key features and design elements of the T-series monitors make uandksound a "studio standard." The series uses a very strict design concept, which is very similar to uandksound's other uandksound products.
-
Page 5: Design Concept
This manual will help you familiarize yourself with the many features of the D-series monitors and how they operate. We hope that you will spend a few minutes familiar with this manual. Thank you for choosing uandksound! Important note: The T-Series monitors were originally packaged in specially designed carton. - Page 6 Resonance means that after removing the drive source, some objects will tend to vibrate at a particular frequency point. Resonance also has a crucial impact on the performance of the speaker. The design element of uandksound is to minimize the resonance of the small drive and the outer casing.
- Page 7 The active sub-filter-T series amplifier contains three active filters. (Subsonic, low pass and high pass). These three filters work together to achieve a seamless integration of the drive components, ensuring smooth spectral balance.
- Page 8 (A) System level adjustment The input sensitivity is adjusted by an adjustment device that is neatly attached to the rear panel (counterclockwise to reduce sensitivity). The adjustment range is from Min to Max. The preset gain is Min, which is sufficient for most situations. Adjustments are usually required only when the user is using a T-series monitor in a surround sound system and needs to balance the level, or if the monitor's source is overheated and cannot be adjusted.
- Page 9 (B) Low frequency adjustment (T6 only) This three-speed switch is used to adjust the low frequency response of the monitor. Poor low frequency components are produced near the wall. Adjust the low frequency adjustment switch to compensate for the over-amplified low frequency response. The type of adjustment that should be taken is determined based on room acoustics to ensure that the monitor has the proper frequency response.
-
Page 10: Connection System
Connection system Turn on the power All connections are completed, all controllers and adjustments should be set to a minimum, and all other equipment should be powered up before the T6 monitor is energized. The power on/off switch is located on the rear panel. Audio mute switch When the switch is placed in the "on"... - Page 11 reverb will be worse (excluding the mixer's reverb). However, when the speaker can not be placed in the best position, the use of low adjustment is a solution. We assume that there are now two different studios, one in the room, the monitor speakers are close to the wall, and in the other room, they are far from the wall.
- Page 12 Bass speaker settings First determine the best position for the woofer. If possible, the settings shown in Figure 3 work best, however, this setting may not be feasible for your room. After the monitor speakers are installed, listen to some audio and video materials that contain low frequency information. If the subwoofer has a phase switch, adjust it to the highest frequency.
- Page 13 7.1 channel surround sound settings The 7.1-channel surround sound unit adds two speakers to the sides of the mixing position, which is very similar to the real surround sound configuration of a movie theater - the difference is that the cinema usually adds extra side surround sound to compensate for the space length of the theater.
-
Page 14: Troubleshooting
3 for replacing the fuse). ・ After the monitor speakers are powered up, the uandksound company logo on the front panel will be illuminated. If not, turn off the power switch and check the AC power fuse. Never use an fuse that is larger than the specified amperage. -
Page 15: Shipping Instructions
Shipping instructions ・ To be shipped back to uandksound as safely as possible, please use the shipping carton and initial packaging when purchasing uandksound monitor speakers. ・ Uandksound is not responsible for equipment damage caused by packaging negligence during shipment. - Page 16 "RMA" serial number. We will not perform any repairs on the equipment without this serial number. ・ Replacement cartons and packaging materials can be used at uandksound Systems, LLC. $26.50 each.