Connect the MS3Pro-PNP ......................... 6 Power up the MS3Pro-PNP ....................... 6 Connection to a MS3Pro-PNP with TunerStudio and a USB or serial cable........6 Calibrate the «TPS» (throttle position sensor) ................. 6 Calibrate the IAT (intake air temperature) and CLT (coolant temperature) if not using the factory one.
Race parts are inherently dangerous and may cause injury or damage if improperly modified or altered before use. Perfect Tuning will not be held liable for and will not pay you for any injuries or damage caused by misuse, modification, redesign, or alternation of any of our products. Perfect Tuning will not...
Page 4
boards, auto tuning and diagnostics you need to purchase the software. It’s possible to download directly TunerStudio at: www.tunerstudio.com/index.php/downloads. When a computer is connected to a MS3Pro for the first time with an USB cable, a driver may be needed: http://www.ftdichip.com/Drivers/VCP.htm Here is a custom dashboard created by users on MsExtra forum.
Software for Android devices Shadow Dash MS is the Android TunerStudio version. You can download it here : https://play.google.com/store/apps/details?id=com.efiAnalytics.shadowdash for 9.99$ MsDroid display real-time data and it’s also possible to edit the tune. The software is completely free! https://play.google.com/store/apps/details?id=com.msdroid. If MsDroid shows a connection error message go to http://www.msextra.com/doc/ms3/files/release/ and downloads your MS3Pro software version (by default 1.5.0) and extract the ms3pro.ini file to the MsDroid/ini folder on your Android...
This indicates that the MS3Pro-PNP is functional. It’s possible to look at the two led on the MS3Pro-PNP. Red is for power to the MS3Pro-PNP and greed is active when fuel pump is ON. 3. Connection to a MS3Pro-PNP with TunerStudio and a USB or serial cable.
This step is very because the timing signal is generated from the CPS (cam position sensor) signals and the CPS can move. This step is here to ensure that the timing of the MS3Pro-PNP is synchronized with the engine. If you do not perform this step, YOU CAN DAMAGE OR DESTROY YOUR ENGINE.
This connector contains the access to all the inputs and outputs to add more functionality to the MS3Pro-PNP. This is the view of the connector on the ECU. Note that the numbers are also noted on the connector plug. See Inputs and Outputs section for more information about the functionality of each pin.
The internal wideband Bosh LSU 4.9 controller is optional. To know if the controller is present inside your MS3Pro-PNP, look at the serial number sticker on the back of the MS3Pro-PNP. When the controller is present, the provided wideband sensor will connect directly to this connector and will output a 0-5v signal on the expansion connector pin #12;...
How to crimp a wire for the expansion or wideband connector without the right crimper. 1. Strip the wire like the picture: 2. Insert the wire into the connector: 3. With long noses pliers fold the small edges. 4. Then fold the long edges: 5.
Connector used to interface the MS3Pro-PNP with a DB-9 serial cable. Remember: only one connection at the time to the MS3Pro-PNP (USB, serial, Bluetooth). A reboot might be required if you change the connection method while the MS3Pro-PNP is powered.
Inputs and outputs List of inputs and outputs Here are all the inputs and outputs for the MS3Pro-PNP that you will use in TunerStudio settings. MS3Pro-PNP Module pin name Location in the MS3Pro-PNP Input Digital Switched In 1 Connected to the expansion connector pin 18.
For more information, refer to the MS3Pro user manual. A/C Control The MS3Pro-PNP is connected to the A/C for idle up. It is possible to control the A/C clutch to disable the A/C when you’re full throttle or based on other conditions.
The conditioner circuits are the same as the crank and cam conditioners. There are four (2) jumpers inside the MS3Pro-PNP that are used to route the signals to the VR conditioner circuits or directly connected to the Digital Frequency Input.
#1 to the ON position. To use the Bluetooth module, you need to pair with the module called PERFECT_TUNING_MS3PNP and enter the password 1234. Note that in every situations, only one connection to the MS3Pro-PNP can be made at the same time (one device, with serial, USB or Bluetooth).
Internal Data logging on SD Card An 8GB SD card is included with each MS3Pro-PNP. It is possible record many days of logs in this internal memory. All logs are time stamped so it’s easy to find the right data log of a specific moment.
Base map All MS3Pro-PNP comes with a default base map that is able to start and run your engine but tuning will be required. 12 Month Limited Warranty Perfect Tuning warrants to the consumer that all products will be free from defects in material and workmanship for a period of twelve (12) months from date of the original purchase.
MS3Pro-PNP dimensions 185mm X 159mm X 38mm (7 ¼ x 6 ¼ x 1 ½ inches) Contact If you have any issues, or questions, you can take a look on www.msextra.com or contact me at support@perfecttuning.net. I can give remote desktop and phone support. Just contact me by email first.
Accessories: Multiple Wideband are available. Please visit http://perfecttuning.net for more information. Fast response GM intake air temperature sensor (open element IAT) GM intake air temperature sensor or coolant temperature sensor (close element). Exhaust gas temperature sensor. Up to 1250 Celsius with interface board. USB-Serial cable for computer or Android device.