Table of Contents
Advertisement
Quick Links
USER MANUAL
AFTER SALES SUPPORT:
WWW.SPTOOLS.COM
IMPORTANT
ALL PERSONS WHO ARE TO USE THIS EQUIPMENT MUST THOROUGHLY READ
AND UNDERSTAND THIS INSTRUCTION MANUAL PRIOR TO OPERATION.
SP61073
1600A JUMP
STARTER LI+
COBALT HIGH
DENSITY POWER
BANK
RETAIN THESE INSTRUCTIONS
AND ATTACH RECEIPT TO
MANUAL FOR FUTURE
NOTE: Proof of purchase must be retained by
the customer as it will be required in the
event of a claim under warranty.
AUSTRALIA: Visit the website's contact page to get in
touch with your local service department.
INTERNATIONAL: Use the county selector to get in touch
with your service department in your country or region.
REFERENCE
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for SP tools SP61073
- Page 1 USER MANUAL SP61073 1600A JUMP STARTER LI+ COBALT HIGH DENSITY POWER BANK RETAIN THESE INSTRUCTIONS AND ATTACH RECEIPT TO MANUAL FOR FUTURE REFERENCE NOTE: Proof of purchase must be retained by the customer as it will be required in the event of a claim under warranty.
-
Page 2: Table Of Contents
CONTENTS Introduction Safety Precautions & Warnings Intended Use Technical Features Technical Specification Operating Instructions Troubleshooting Warranty Details... -
Page 3: Introduction
The SP61073 Li Cobalt Power Bank, Jump-starter, automatically provides reverse polarity and short circuit protection, preventing serious battery damage, in the event of miss-... -
Page 4: Safety Precautions & Warnings
△ ! WARNING △! Safety Instructions for Charger & Battery 1. Do not use a damaged appliance. If the electrical cord of the charger is damaged have it repaired or replaced by a qualified repair agent immediately. 2. Do not charge the Cobalt Power Bank, Jump-starter inside a box or container;... -
Page 5: Intended Use
Intended Use • Only for use in non-explosive, dry environments. • Never use or put the unit down in any liquid, oil or water. As Jump starter: The Cobalt Power Bank is intended for use on 12V vehicles petrol and diesel up to 10 litres. -
Page 6: Technical Specification
Technical Specification: Input: 18V – 1.5A 12V via jump start output port: Jumpstart (max clamp opening 45mm) 12V port: Power or charge 12V accessories 19V port: Power or charge 19V laptops 5V USB 2.1A output: Mobile phones, Tablets, Cameras etc. Battery Capacity: 28000mAh Start Current: 800A Peak Current: 1600A... - Page 7 2. Li Power Bank Charging Instruction: The Li Cobalt Power can be connected to home (240v) or car charger (12v), once input power is connected the display flashes red with the word "IN". 240v charging: Plug the home adaptor into the 240v power point, next connect to the 18V 1.5A input port of the Li Cobalt Power Bank.
- Page 8 4. Power or Charge 12V & 19V Devices / Laptop (fig. 3) Turn the power button to the “ON” position. Insert the power lead (fig. 3) into the correct output socket on your Li Power Bank, you can choose between 12V 3.5A or 19V (fig.
-
Page 9: Troubleshooting
6. Once the vehicle has started turn the power button to the “OFF” position, remove jumper cable from Li Power Bank and disconnect RED and BLACK clamps from the vehicle battery terminals. 7. Note: Once the engine is running, be sure to allow enough time for the vehicles alternator to restore charge to the vehicles battery before turning it off again. -
Page 10: Warranty Details
To the extent permitted by law and subject to this Limited Warranty, and as part of the terms of the sale of the equipment or part thereof: SP Tools shall not be liable for any form of loss, damage, cost, injury or harm of any kind (whether direct, indirect, special or consequential) howsoever arising from the use or supply of the equipment to the purchaser.
Need help?
Do you have a question about the SP61073 and is the answer not in the manual?
Questions and answers