E-Z-RECT TYPE 1 Assembly Instructions

TYPE 1 Boltless Shelving
POST
CONNECTOR
TWIST LOCK
POST
SCREWDRIVER OR
CHAINSAW WRENCH
S T E P O N E
Place post flat on the ground so that Post Connector slots
are on the inside and the seam is on the outside. Post
Connector slots are adjustable every 12" (305mm).
Arrange Post Connectors at desired location, normally
evenly spaced, with one always at top and bottom of
post.
POST CONNECTOR MUST BE LOCKED FOR SAFETY
TAB NOT LOCKED
LOAD CAPACITIES (IN LBS.) Maximum evenly distributed static load per pair of connectors
SHELF LENGTH
PB Frame Connectors
B Frame Connectors
with L Tie & O Shelf Support
WB Frame Connectors
with WT Combination Tie Bar & Shelf Support
HD Frame Connectors
with WT Combination Tire Bar & Shelf Support
XHD Frame Connectors
with WT Combination Tie Bar & Shelf Support
Connectors are designed for an overall Safety Factors of 1.66 to 1 which conforms to AISI Standards. Deflection is limited to 1/140 for spans.
*
Two WT Combination Tie Bar and Shelf Supports must be used.
PLEASE FOLLOW ASSEMBLY INSTRUCTIONS. DO NOT USE SHELVES OR CONNECTORS WITH COMPONENTS OTHER THAN E-Z-RECT PRODUCTS.
LOCK
FIFTH
SAFETY
LOCK
THIRD
LOCK
FIRST
FRAME ASSEMBLY
S T E P T W O
Starting from the bottom tap in one side of the Post
Connector and LOCK IMMEDIATELY. Then tap in
and lock the other side. The post will have to be
spread lightly as you work your way up the post. Use
a 1/4" or a 3/8" screwdriver or chainsaw wrench to
lock connectors. Assembly time is approximately 1 to
2 minutes per 84" (2134mm) frame.
LOCKED TAB FULLY LOCKED
36" 42" 48" 60" 66"
400 340 300 150 -
700 620 550 400 -
1400 1100 900 530
-
1200 1050 950 700 575
1800 1640 1500 1200 1030
1650 1550 1400 1000 900
2000 1950 1900 1700 1600
- - - - -
- - 2400 2400 2400
BLACK PLASTIC TOP
OR BOTTOM CAP
LOCK
Install top cap after assembly.
SIXTH
SHELF CLIP
4 required per shelf level
(2 right hand and 2 left hand).
Use with metal shelves.
LOCK
FOURTH
LOCK
SECOND
72" 96"
- -
- -
- -
480 -
900 - SECTIONAL SHELF
Use with shelf bar. Frame connectors
450
800
& Combination tie bar required for
*
1500
900
heavier loads and longer spans.
-
-
*
2400
1700
POLYPROPYLENE FLOOR PROTECTOR
Polypropylene levelling shim available.
E-Z-RECT MANUFACTURING LTD.
Head Office: North Vancouver, P: 604 929 5461 Eastern Sales: Mississauga, P: 905 564 0890
Email: sales@ezrect.ca Web: www.ezrect.ca Email:
ONLY FOUR BASIC COMPONENTS
1. Post
2. Post Connector
PB FRAME CONNECTOR
Use particle board shelves, or use
PB 90° connectors for metal shelves.
B FRAME CONNECTOR
Use with metal or wood shelves.
WB FRAME CONNECTOR
Use with metal or wood shelves.
CONNECTOR LOCKING CLIP
Use to lock connectors for mezzanine,
catwalk & seismic applications.
XHD FRAME CONNECTOR
Use with metal or wood shelves.
HD FRAME CONNECTOR
Use with metal or wood shelves. All upright posts are slotted 2" (51mm) centers
For maximum shelf adjustment.
COMBINATION TIE BAR
Fits WB & HD frame connectors
for added strength.
Allow CTB hook to snap into
Connector slot with its own spring.
POST CONNECTOR
Use for making up end frames.
SHELF BAR
2 required per shelf level.
Use any frame connector
(except PBL 90°) or on shelf clips
POST SPLICE
• Use for extending post.
• Join two internal post splices together to form a cross.
Hammer into one post half way.
• Place top post over post splices and tap down carefully until
posts meet.
• Attach two external post splices on the outside of the joined
posts and secure them together with bolts and nuts.
UK Sales: Oxon, P: 01993 779494
torontosales@ezrect.ca Web: www.ezrect.ca Email: mail@ezrshelving.com
Assembly Instructions
3. Frame Connector
4. Shelf (metal or particle board)
FRAME
CONNECTOR
POST
SHELF
HEIGHT
3' TO 20'
POST
CONNECTOR
WIDTH
DEPTH
3' TO 8'
1' TO 4'
Web: www.ezrshelving.com
© E-Z-Rect Manufacturing Ltd. T1 Revision May 2019