Advertisement
Quick Links
Operating Instructions
Beer Bottle Rinsing Machine
Installation, First commissioning
Rinsing
Emptying the machine, Internal cleaning
Possible Troubleshooting
Wiring diagram
Technical data
Bottle basket (Assembly)
Important tip for rinsing
Please read the whole Operating Instructions
before using the machine!!!!!
GS 21
September 2016
Erich Baumgartner
Gastronomiemaschinengroßhandel
Hauptstrasse 4
A - 5222 Munderfing
Tel.: 0043 / 7744 / 20 12 10
Fax: 0043 / 7744 / 20 12 12
E-mail: verkauf@gastrohandel.at
Page
2,3
Page
Page
5,6
Page
Page
8 - 10
Page
11
Page
12 - 15
Page
16
4
7
Advertisement
Related Manuals for ebatec GS 21
Summary of Contents for ebatec GS 21
- Page 1 Operating Instructions Beer Bottle Rinsing Machine GS 21 September 2016 Erich Baumgartner Gastronomiemaschinengroßhandel Hauptstrasse 4 A - 5222 Munderfing Tel.: 0043 / 7744 / 20 12 10 Fax: 0043 / 7744 / 20 12 12 E-mail: verkauf@gastrohandel.at Installation, First commissioning...
- Page 2 Installation and Connection of the Machine The machine is equipped with the following accessories: - Power supply 5 x 4 mm² connected to the an rinsing machine, - Supply hose with the fitting connecting pieces and seals, - Drain hose, 1 bottle carrier basket, 1 carrier for crates The following conditions described on the installation plan are necessary: - The water drain at ground level.
- Page 3 Firstly, manually tighten the nut of the supply hose then by using a pipe wrench. Do not over tighten the hose clamp of the drain hose. Take the container with chemicals, drill a hole of about 8 mm Ø into the lid. Insert the hose through the lid and fix the weight and the suction filter.
- Page 4 Rinsing Check if the suction filter is in the provided position. Insert the overflow pipe into the drain. Place the surface filter into the machine (first remove the protective film). Close the door and press the mains switch (1) The green indicator light (3) is illuminated. The automatic filling of the tank is performed via the inlet valve, the pressure increase pump and via the rinsing system.
- Page 5 Emptying the Machine Press the mains switch (1). The control lamp is switched off. Open the door, take out the basket with the clean beer bottles or crates (if there is a basket in the machine), pull out the overflow pipe the rinse water will automatically drain out of the tank.
- Page 6 Take off the pump filter and the surface filter and rinse them under flowing water. Take out the rinsing arms by slightly turning them to the left. To perform the cleaning, it is recommended to place the beer crates on the crate carrier included in the delivery.
- Page 7 Possible Troubleshooting Malfunction Possible cause / Remedy The power supply to the machine is It is not possible to switch on the machine interrupted, Cause within the machine, Contact the after-sales service The check valve provided by the customer The machine is not being filled with water is closed, The air trap is soiled –...
- Page 8 Page 8...
- Page 9 Page 9...
- Page 10 Page 10...
- Page 11 Technical data: Hourly output about 190 bottles/h Rinsing time: 6 min 30 sec. Pump capacity: 736 W Circulation rate: 330 l / min. Tank heater: 2 x 4500 W Overall connected load: 9736 W Voltage: 400 volts Tank contents: 29 l Water consumption/Rinsing process: about 7.8 l Water pressure:...
- Page 12 Bottle Basket The system of our bottle basket is suitable for almost all types of bottles. No matter if you need to rinse NRW-, long necked, NF- or flip top bottles. Scope of delivery: 1 pc basic basket 8 pcs support rails 32 pcs locknuts + reserve 36 pcs support rails 72 pcs clips + reserve...
- Page 13 First check, at which height the bottom support rail shall retain your bottle. At this, make sure that the bottle opening should only be a few mm above the bottom. The following distances of the support rails are suitable for almost all bottles: View of the basket from the front: From the left to the right: 2 holes free –...
- Page 14 After having determined the height of the seats for the bottles by means of the supporting bars fix the support rails on the base frame. The holes are drilled in the support rails from the centring. Therefore, the holes to the bottom for the front and rear support rail, and the holes towards the top for the lateral support rail.
- Page 15 Perform the same process for the top support rail. Please note, that the bottles are as vertical as possible in the position. Please observe that the top support rails are not at the same height as the labels of the bottle. The labels should be collected on the support filter when they are detached from the bottle.
- Page 16 Please proceed as follows in order to check if the fresh water nozzles exactly spray into the bottle: Switch off the machine and remove the overflow pipe. Seal the “drive nozzle” (on the right) at the top re-rinsing arm and fix the arm. Place the bottle basket with 4 bottles in the first row.
Need help?
Do you have a question about the GS 21 and is the answer not in the manual?
Questions and answers