Advertisement
■ Part Names
TP65
TP65S
Pad
Left Rim
(The TP65S contains switches in its left and right rim sections.)
■ Setting Up
After setting up your rack system (Yamaha RS70, etc.) or a standard tom stand (Yamaha
WS series, etc.), attach the TP65/65S as shown in the diagram below.
Insert the tom holder (hexagonal bar) on your rack or tom stand into the pad, and firmly
tighten the clamp bolt to secure.
Insert
Clamp Bolt
■ Specifications
TP65
Dimensions
220(diameter) X 61(H) (excluding the clamp bolt)
Weight
980g (including the clamp bolt)
Sensor System
TP65: Trigger Sensor (piezo-electric) x1
Output Jack
Standard Monaural Phone Jack
* Improvements may result in a change in the specifications and/or design of the product without notice.
Pad
Clamp Bolt
Output jack
Right Rim
Tom Holder
TP65S
Trigger Sensor (piezo-electric) x1/
Rim switch (2 zones) x1
Standard Stereo Phone Jack
■ Connections
Use the supplied stereo phone cable to connect the pad's output jack with the input jack
(SNARE, TOM 1, etc.) on the drum trigger module (DTXPRESS/DTX/DTXTREME). Con-
nect the cable's L-shaped plug to the TP65/65S.
The manner in which the TP65/65S will function corresponds to the INPUT numbers on the
DTX Series Drum Trigger Module shown in the chart below.
❇ Connect to the input that is used for the tom pad on your drum trigger module. (Refer to the Owner's
Manual that came with the drum trigger module for further information.)
MODULE
Input Number
TP65 TP65S
DTXTREME s
1〜8
●
◎
9/10〜15/16
●
●
DTXPRESS
1
●
△
DTXPRESS
2,6,7
●
◎
3〜5,8
●
○
9/10
●
●
DTXTREME
1〜5
●
△
6〜8
●
○
9/10〜15/16
●
●
DTXPRESS
1
●
△
2〜8
●
○
9/10
●
●
DTX
1〜8
●
○
9/10,11/12
●
●
❇ Make sure that a stereo cable is used when connecting the TP65S to the module. If a monaural cable
(Plug has one black rings) is used, the voices set to the right/left rim will not be produced.
Adjusting the Voice Volume
To change the volume of the voice(s) assigned to the TP65/65S, use the [VOICE] Edit
Mode in the DTX Series Drum Trigger Module. Please refer to the Owner's Manual
that came with your module for further information.
SPECIAL MESSAGE SECTION
NOTICE: Service charges incurred due to a lack of knowledge relathing to how a function or effect works (when the unit is operating
as designed) are not covered by the manufacturer's warranty, and are therefore the owners responsibility. Please study this manual
carefuly and consult your dealer before requesting service.
ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely
believe that our products and the production methods used to produce them, meet these goals. In keeping with both the letter and the
spirit of the law, we want you to be aware of the following:
Warning: Do not attempt to disassemble.
Disposal Notice: Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end,
please observe all local, state, and federal regulations that relate to the disposal of products that contain lead, plastics, etc. If your
dealer is unable to assist you, please contact Yamaha directly.
NAME PLATE LOCATIOIN: The name plate is located on the bottom of the product. The model number, serial number are located on
this plate.
You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as
a permanent record of your purchase.
Model : TP65
Model : TP65S
Purchase Date
PLEASE KEEP THIS MANUAL
Output jack
Insert
● ：A single voice is assigned to, and produced by the pad.
○ ：Individual voices can be assigned to, and produced by the pad
and rim (2 voices).
◎ ：Individual voices can be assigned to, and produced by the pad,
left rim, and right rim (3 voices).
△ ：Individual voices can be assigned to, and produced by the pad,
and right rim (2 voices: the left rim switch is inactive).
Serial No.
Serial No.
Printed in Indonesia
WF75880
Advertisement
