Page 1
Home / BluSnap User Guide BluSnap User Guide Thank you for purchasing BluSnap and becoming a part of the growing BluArmor tribe! This page has everything you need to know about how to install, use and maintain your BluSnap. Please read through the safety instructions and...
Page 2
The re-chargeable battery in your BluSnap comes with very little initial charge for shipping-safety reasons. Before you use BluSnap for an extended period of time, please charge the device. The gure below illustrates how you charge your BluSnap. As shown, lift the right ap of the top-cover https://bluarmorhelmets.com/pages/blusnap_userguide...
Page 3
~ 10 hours of riding on a full charge. You will not be able to power BluSnap while it is charging. If you are going on a long ride, make sure that BluSnap is fully charged and ready to go! Turning your BluSnap ON/OFF BluSnap's ON/OFF switch is visible on the top cover.
Page 4
The water inlet (as the name implies) is the inlet through which you will ll the reservoir. To locate the water inlet, please lift the left-side ap of the top cover (shown in the gure below). BluSnap has a narrow pipe to its water reservoir. It is advised to use a small glass/tumbler/bottle while pouring water into BluSnap.
Page 5
Step 3: Ride for some time (~15 minutes) before opening the water-reservoir lock as the cooling lter will be wet to start with because of Step 2 The current version of BluSnap does not have a water-level indicator. This is planned for subsequent generations https://bluarmorhelmets.com/pages/blusnap_userguide...
The gure below shows how BluSnap attaches to your helmet. Insert the helmet's jaw between the back wall of BluSnap's main body and the two air vents, and then pull the strap around the back of the helmet. Let the strap go as close to the visor and as high as possible at the back of the helmet giving the strap the maximum stretch you can achieve - this improves the hold that the strap has on the main body.
Page 7
BluSnap User Guide | BluArmor Helmets With some helmets, the jaw can be very thin and extra adhesion might be needed between BluSnap and the helmet. For this purpose, we have provided a velcro ap as part of the strap. The mating velcro unit is part of your package.
Page 8
5/22/2018 BluSnap User Guide | BluArmor Helmets A short tutorial explaining how you can use the velcro strips that come with your BluSnap package to improve the adhesion between your helmet and BluSnap is embedded below. Strap Velcro Installation SUBSCRIBED Cleaning/Replacing the Cooling Filter Cartridge https://bluarmorhelmets.com/pages/blusnap_userguide...
Page 9
CAUTION: If the cooling lter is not cleaned periodically, its life-time will reduce. Cleaning the Grill/Coarse Filter BluSnap's grill integrates a coarse lter to block large dust particles, insects, etc. This coarse- lter should be inspected and cleaned on a regular basis. To pull out the grill, simply remove the top cover and slide out the grill (as shown in the gure) https://bluarmorhelmets.com/pages/blusnap_userguide...
Page 10
The coarse lter can be cleaned/dusted using a toothbrush. Strap Options - Swapping them in/out BluSnap comes with multiple strap options and you can easily swap them in/out. The strap slides in/out through the strap-guides on the main body as shown in the gure. Replacement straps are available on our website.
Page 12
5/22/2018 BluSnap User Guide | BluArmor Helmets MAIN MENU ABOUT POLICES SOCIAL BLUARMOR Home Privacy Policy Facebook FAQ's Order Now Terms and Twitter Contact Us Conditions https://bluarmorhelmets.com/pages/blusnap_userguide 12/13...
Need help?
Do you have a question about the BluSnap and is the answer not in the manual?
Questions and answers