Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Innophase Talaria TWO
Summary of Contents for Innophase Talaria TWO
- Page 1 INP2045 Talaria TWO (INP2045) IEEE 802.11 b/g/n, BLE Hardware User Guide Version 0.4 1/5/2020 InnoPhase, Inc. Copyright ©InnoPhase, Inc. 2017, All Rights Reserved 6815 Flanders Drive PROPRIETARY and CONFIDENTIAL San Diego, CA 92121 innophaseinc.com Subject to Change Without Notice...
-
Page 2: Table Of Contents
1.3 ESD Precaution ............................3 Talaria TWO Description and Operation ..................... 4 Talaria TWO Block Diagram ........................5 Talaria TWO Maximum Transmit Power and Operating Temp ..............5 Talaria TWO Schematics ..........................6 PCB Layout ............................7 FTDI Layout and Port Connections....................8 5.3 Talaria TWO Module Pinout ........................ -
Page 3: Introduction
1.2 Pre-requisites Following are pre-requisites for the quick start: 1. A Windows or Linux PC with one USB port to connect to Talaria TWO SDK board. A Linux PC is generally recommended over Windows. 2. A COM port console application such as PuTTY. -
Page 4: Talaria Two Description And Operation
HW interface board developed for evaluation, SW development, and verification of Talaria module product. The Talaria TWO module (INP2045) is shown in Figure.4-1. It is a very small form factor PCB at 19mm x 20mm, designed to be soldered down as a module on end product interface boards. -
Page 5: Talaria Two Block Diagram
INP2045 3. Talaria TWO Block Diagram 4. Talaria TWO Maximum Transmit Power and Operating Temp Mode Maximum TX Power Wi-Fi: DSSS, 1Mbps 18 dBm Wi-Fi: CCK, 11 Mbps 18 dBm Wi-Fi: OFDM, 54 Mbps 15 dBm Wi-Fi: MCS7, 65 Mbps... -
Page 6: Talaria Two Schematics
5. Talaria TWO Schematics Figure 5-3 INP2045 Module schematic. For evaluation and SW development, the INP2045 Talaria TWO module is installed on an SDK board which provides communication to an external PC though a standard USB interface. An additional 40 pin connector on the SDK provides access to UART, JTAG and SPI communication with peripheral devices as well as exposes all the INP2045 GPIO for development and integration of the application. -
Page 7: Pcb Layout
INP2045 Figure 5-4 Pinout of 40 Pin Connector 5.1 PCB Layout InnoPhase, Inc. Copyright ©InnoPhase, Inc. 2017, All Rights Reserved 6815 Flanders Drive PROPRIETARY and CONFIDENTIAL San Diego, CA 92121 innophaseinc.com Subject to Change Without Notice... -
Page 8: Ftdi Layout And Port Connections
The Talaria TWO SDK board uses an FTDI 4232h quad high-speed USB multi-purpose serial device to interface the Talaria TWO device to a host for evaluation and development. The FTDI device implementation is given below: FTDI Bus Interface to Talaria TWO... -
Page 9: Pin Description
AGND Ground connection ADC_IN ADC Analog Input (voltage range is 0…1 V) AGND Ground connection InnoPhase, Inc. Copyright ©InnoPhase, Inc. 2017, All Rights Reserved 6815 Flanders Drive PROPRIETARY and CONFIDENTIAL San Diego, CA 92121 innophaseinc.com Subject to Change Without Notice... -
Page 10: Antenna
INP2045 6. Antenna Talaria TWO module has a proprietary integrated/printed antenna. It is a Double-sided Inverted F (IFA) antenna and has been implemented as printed PCB elements. By design and verification, Antenna does not require any additional matching component if the module is used as standalone product. -
Page 11: Fcc/Ised Regulatory Notices
INP2045 9. FCC/ISED Regulatory Notices 9.1 Modification statement Changes or modifications made to this equipment not expressly approved by Innophase Inc. may void the FCC authorization to operate this equipment. 9.2 Interference Statement This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). -
Page 12: Labeling Requirements For The Host Device
"Contient", ou un libellé similaire exprimant la même signification, comme suit: • Contient FCC ID: 2AVAL-INP2045 • Contient IC: 25715-INP2045 InnoPhase, Inc. Copyright ©InnoPhase, Inc. 2017, All Rights Reserved 6815 Flanders Drive PROPRIETARY and CONFIDENTIAL San Diego, CA 92121 innophaseinc.com Subject to Change Without Notice... -
Page 13: Disclaimers
InnoPhase Incorporated product can reasonably be expected to result in personal injury, death or severe property or environmental damage. InnoPhase Incorporated and its suppliers accept no liability for inclusion and/or use of InnoPhase Incorporated products in such equipment or applications and such inclusion and/or use is at the customer’s own risk. -
Page 14: Support Details
Knowledge Database • Discussion Forums • Customer Web Portal InnoPhase has offices in US, Asia and Europe providing outstanding support for our customers. InnoPhase, Inc. Copyright ©InnoPhase, Inc. 2017, All Rights Reserved 6815 Flanders Drive PROPRIETARY and CONFIDENTIAL San Diego, CA 92121 innophaseinc.com... -
Page 15: Abbreviations
Version Release Notes 1/5/2020 FCC/IC Notices added 9/13/19 ESD Precaution added 9/13/19 Initial release 9/12/18 Initial Draft InnoPhase, Inc. Copyright ©InnoPhase, Inc. 2017, All Rights Reserved 6815 Flanders Drive PROPRIETARY and CONFIDENTIAL San Diego, CA 92121 innophaseinc.com Subject to Change Without Notice...