Related Manuals for R3 EchoRing ER-EB 1000M
Summary of Contents for R3 EchoRing ER-EB 1000M
- Page 1 ECHORING ETHERNET BRIDGE User Manual ER-EB 1000M (Version for USA and Canada) Contact Information: R3 – Reliable Realtime Radio Communications GmbH Bismarckstraße 10-12 www.echoring.com 10625 Berlin contact@r3coms.com...
- Page 2 Revision: 1 © by R3 – Reliable Real-time Radio...
-
Page 3: Table Of Contents
5.4 Replace an Ethernet Bridge™ ........11 © by R3 – Reliable Real-time Radio... - Page 4 Revision: 1 © by R3 – Reliable Real-time Radio...
-
Page 5: General Terms Of Use Of This Document
1 General Terms of Use of this Document • It is the user’s responsibility to check regularly and ensure they have downloaded the latest version of this manual, as R3 may edit, revise, or improve product documenta- tion over time. -
Page 6: Please Observe The Following Notes
TIP — Text in this format is information explaining the use of the product. ATTENTION — Text in this format must be observed in order to avoid malfunction and/or damage, or to avoid potential security risks. 2. Please Observe the Following Notes Page 2 of 11 © by R3 – Reliable Real-time Radio... -
Page 7: Product Information
(1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation. ATTENTION — Changes or modifications made to this equipment not expressly approved by R3 may void the FCC authorization to operate this equipment. -
Page 8: Rss-210 Of Ised
(e.i.r.p.) is not more than that permitted for suc- cessful communication. That the device for the band 5,150-5,250 MHz is only operated indoors to reduce potential for harmful interference to co-channel mobile satellite systems. 3. Product Information Page 4 of 11 © by R3 – Reliable Real-time Radio... -
Page 9: Installation
Figure 4-II: DIN rail mounting 3. Push the device downwards so it snaps into place. TIP — To release device from DIN rail, push the device downwards while pulling outwards. © by R3 – Reliable Real-time Radio Page 5 of 11 4. Installation... -
Page 10: Wall Or Mast Mounting
ATTENTION — The signal cable for digital input must be carried in the same cable as the power supply and functional ground if the line length exceeds 3 meters. 4. Installation Page 6 of 11 © by R3 – Reliable Real-time Radio... -
Page 11: Led Indicators
Device does not run. Device is either out of range of other devices or a software related problem has occurred. • ETH + Green flashing Device is in Performance Analyzer mode. Table 4-iii: Explanation of LEDs © by R3 – Reliable Real-time Radio Page 7 of 11 4. Installation... -
Page 12: Web-Based Configuration Interface
2. In Web User Interface, take a look at ”Echoring Deployment”. Connected devices are shown in the paring view there. Click the IP address to pair all devices or click each device to include/exclude it. 5. Web-based Configuration Interface Page 8 of 11 © by R3 – Reliable Real-time Radio... - Page 13 If no prioritized traffic is set, all data is treated as equally critical. © by R3 – Reliable Real-time Radio Page 9 of 11 5. Web-based Configuration Interface...
- Page 14 Length (F) and Latency (G), this one selected parameter will be given best possible value automatically pending on the other parameters input value. Exact Config disable this function. 5. Web-based Configuration Interface Page 10 of 11 © by R3 – Reliable Real-time Radio...
-
Page 15: Replace An Ethernet Bridge
To replace a device, all devices in the pertaining network must be reconnected and then reconfigured with the replacement device, according to the procedure in Section 5.3 above. © by R3 – Reliable Real-time Radio Page 11 of 11 5. Web-based Configuration Interface...
Need help?
Do you have a question about the EchoRing ER-EB 1000M and is the answer not in the manual?
Questions and answers