Related Manuals for R3 ECHORING ER-EB 1000M
Summary of Contents for R3 ECHORING ER-EB 1000M
- Page 1 ECHORING ETHERNET BRIDGE User Manual EREB 1000M (EU version) r20.08 Contact Information: R3 – Reliable Realtime Radio Communications GmbH Bismarckstraße 1012 www.echoring.com 10625 Berlin contact@r3coms.com...
- Page 2 Revision: 1.2 © by R3 – Reliable Realtime Radio...
-
Page 3: Table Of Contents
5.5 Update devices ........... . 11 © by R3 – Reliable Realtime Radio... - Page 4 Revision: 1.2 © by R3 – Reliable Realtime Radio...
-
Page 5: General Terms Of Use Of This Document
1 General Terms of Use of this Document It is the user’s responsibility to check regularly and ensure they have downloaded the latest version of this manual, as R3 may edit, revise, or improve product documentation over time. The user must ensure the product is used correctly according to this document’s guidelines, in particular observing all relevant standards and regulations. -
Page 6: Please Observe The Following Notes
ATTENTION — Text in this format must be observed in order to avoid malfunction and/or even damage, or to avoid security risks. EXAMPLE — Text in this format provides examples. 2. Please Observe the Following Notes Page 2 of 11 © by R3 – Reliable Realtime Radio... -
Page 7: Product Information
• 2011/65/EU Restriction of the use of certain hazardous substances (RoHS), and • 2014/53/EU Radio equipment (RED). Additional information (e.g. declaration of conformity, documents, test reports, restrictions, etc.) can be found on www.echoring.com. © by R3 – Reliable Realtime Radio Page 3 of 11 3. Product Information... -
Page 8: Installation
Figure 4II: DIN rail mounting 3. Push the device downwards so it snaps into place. TIP — To release device from DIN rail, push the device downwards while pulling outwards. 4. Installation Page 4 of 11 © by R3 – Reliable Realtime Radio... -
Page 9: Wall Or Mast Mounting
ATTENTION — The signal cable for digital input must be carried in the same cable as the power supply and functional ground if the line length exceeds 3 meters. © by R3 – Reliable Realtime Radio Page 5 of 11... -
Page 10: Led Indicators
Device does not run. Device is either out of range of other devices or a software related problem has occurred. • ETH + Green flashing Device is in Performance Analyzer mode. Table 4iii: Explanation of LEDs 4. Installation Page 6 of 11 © by R3 – Reliable Realtime Radio... -
Page 11: Webbased Configuration Interface
5.2 Set up and access Web User Interface 1. Arrange and connect a PC, the R3 Configuration Server and the EchoRing Ethernet Bridges, intended to be in the same network or subnetwork, to the switch, according to Figure 5I: Figure 5I: Configuration setup... - Page 12 Byte Index, counted from the start of the MAC header, and its Byte Value. EXAMPLE — Profinet: EtherType 0x92 ← Byte Values MAC header 0x88 → | → | Byte index 12 5. Webbased Configuration Interface Page 8 of 11 © by R3 – Reliable Realtime Radio...
- Page 13 TIP — To ensure the network can facilitate the application traffic’s cycle time, packet length and data rate, begin with setting lower reliability, then increase as necessary after all other parameters have been set. © by R3 – Reliable Realtime Radio Page 9 of 11 5. Webbased Configuration Interface...
- Page 14 8. Click ”Deploy Configuration” to input the configuration into the devices. 9. Power cycle the devices and disconnect from the switch. 10. Connect each device to their respective, MACaddress configured, device(s). 5. Webbased Configuration Interface Page 10 of 11 © by R3 – Reliable Realtime Radio...
-
Page 15: Replace An Ethernet Bridge
2. Click ”Run Update” to install the listed update on each device on the screen. 3. The update is complete. 4. Click ”Mode” to go back to the main page. © by R3 – Reliable Realtime Radio Page 11 of 11 5. Webbased Configuration Interface...
Need help?
Do you have a question about the ECHORING ER-EB 1000M and is the answer not in the manual?
Questions and answers