Subscribe to Our Youtube Channel
Related Manuals for Parabit Systems MMR2
Summary of Contents for Parabit Systems MMR2
- Page 1 Parabit Systems Inc. MMR2 Installation and Service Manual Parabit Systems, Inc. 35 Debevoise Avenue Roosevelt, NY 11575...
- Page 2 NOTICE Copyright © 2019 by Parabit Systems, Inc. All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the written permission of the publisher.
-
Page 3: Table Of Contents
Chapter 2 Post-Installation Checks and Testing Post-Installation Checks............................13 Default Settings............................13 Preliminary Tools and Materials........................14 Preliminary MMR2 Hardware Check ......................14 Visual Inspection of the MMR2 Card Reader...................15 Post-Installation Testing .............................15 Main Card Reader Tests ..........................16 Additional Test Procedures for the MMR2 Card Reader ................17 Troubleshooting ..............................18... - Page 4 Table of Contents This page intentionally left blank.
-
Page 5: Preface
ACS-1EUL, ACS Enterprise, AFH Service, AVA, AXSView Service, MMR2, and SkimGard are registered trademarks of Parabit Systems Inc. or its subsidiaries in the United States and/or other countries. Parabit Systems, Inc. and Parabit are trademarks of Parabit Systems Inc. or its subsidiaries in the United States and/or other countries. -
Page 6: How To Use This Guide
WARNING: INDICATES A POTENTIALLY HAZARDOUS SITUATION THAT, IF NOT AVOIDED, COULD RESULT IN SERIOUS INJURY. CAUTION: Indicates a hazardous situation that, if not avoided, could result in data loss or product damage. Note: Indicates additional information. MMR2 Installation and Service Manual Ver 1... -
Page 7: Navigating This Manual As A Pdf
Search. Every instance of the search term that appears in the manual will display in the Search win- dow. Click on any of the instances to jump directly to that section. Contact Us Parabit Systems, Inc. 35 Debevoise Avenue Roosevelt, NY 11575 1 (888) 3-PARABIT MMR2 Installation and Service Manual Ver 1... - Page 8 Preface This page intentionally left blank. MMR2 Installation and Service Manual Ver 1...
-
Page 9: Chapter 1 Mmr2 Card Reader Installation
1.2 Electrical Installation .......................8 1.1 MMR2 Card Reader Installation 1.1.1 Overview The MMR2 uses Near Field Communication (NFC) to read contactless EMV cards and mobile devices as well as magnetic stripe cards. 1.1.2 MMR2 Install Diagrams The drawings on the next 2 pages contain basic installation examples to assist with proper placement of the MMR2 card reader. - Page 10 MMR2 Card Reader Installation MMR2 Card Reader Installation Note: Although the diagrams reference SkimGard (IMSR) readers, these diagrams should be used for MMR and MMR-BT installs, as well. MMR2 Installation and Service Manual Ver 1...
- Page 11 MMR2 Card Reader Installation MMR2 Card Reader Installation MMR2 Installation and Service Manual Ver 1...
-
Page 12: Electrical Installation
1.2 Electrical Installation 1.2.1 MMR2 Wiring The wiring for the MMR2, including all of the input and output termination points, is shown in the dia- grams on the following pages. Take care to wire all ends (card reader, circuit boards, door locks and additional power sources) cor- rectly and to label the sheathed cables for input devices (card readers, exit switches, door-sense switches, sensor devices) and output devices (electrical door locks, alarm controllers, etc.). - Page 13 Electrical Installation MMR2 Card Reader Installation Note: The wiring diagram below applies to both the ACS-1E and ACS-1EUL. MMR2 Installation and Service Manual Ver 1...
-
Page 14: Acs-1Eul Card Reader And Input Device Wiring
MMR2 Card Reader Installation Electrical Installation 1.2.1.2 ACS-1EUL Card Reader and Input Device Wiring The other ends of the sheathed cables and their connection to various ACS-1EUL input devices is shown below. MMR2 Installation and Service Manual Ver 1... - Page 15 Electrical Installation MMR2 Card Reader Installation The wiring configuration for the Second card reader board is similar to that of the Controller. MMR2 Installation and Service Manual Ver 1...
- Page 16 MMR2 Card Reader Installation Electrical Installation ACS-1EUL System with Input & Output Sockets and Terminations MMR2 Installation and Service Manual Ver 1...
-
Page 17: Chapter 2 Post-Installation Checks And Testing
Once the MMR2 card reader has been installed, its functionality must be thoroughly tested. 2.1.1 Default Settings Each MMR2 leaves the Parabit factory after passing a full set of operational tests. Any test configura- tions are then removed and the MMR2 is returned to its default configuration. -
Page 18: Preliminary Tools And Materials
Make sure the white wires from the card readers are properly connected to the white wires of the Tamper-Detect switch in the mounting collar or box. Make sure the card reader is properly seated in its mounting collar or box and the Tamper-detect switch “finger” is depressed. MMR2 Installation and Service Manual Ver 1... -
Page 19: Visual Inspection Of The Mmr2 Card Reader
NFC Logo: NFC Logo must be present and positioned along the LED side in the direction shown in the picture. 2.2 Post-Installation Testing Review the diagrams below and complete the tests for the MMR2 card reader. MMR2 Installation and Service Manual Ver 1... -
Page 20: Main Card Reader Tests
Post-Installation Checks and Testing Post-Installation Testing 2.2.1 Main Card Reader Tests MMR2 Installation and Service Manual Ver 1... -
Page 21: Additional Test Procedures For The Mmr2 Card Reader
Field technicians installing the MMR2 system should possess a smartphone with a digital wallet installed containing one active credit card. When planning to perform an MMR2 skim test, a device that operates as an NFC reader is required. Begin by turning on the ACS-1E or ACS-1EUL controller and performing MMR2 System Configuration. -
Page 22: Troubleshooting
Post-Installation Checks and Testing Troubleshooting Complete the following tests to confirm the normal operation of the MMR2 system. 2.3 Troubleshooting Follow the procedure below to troubleshoot common MMR2 card reader issues. Is the Card Reader reading cards? • If no, what color is the LED on the reader? •...
Need help?
Do you have a question about the MMR2 and is the answer not in the manual?
Questions and answers